Teledyne M100E manual Trouble Shooting And Repair, Mounting Screws, User Notes, Relay PCA, Rev B3

Page 21

Relay PCA 04523

Addendum to E-Series Operator Manuals

3. TROUBLE SHOOTING AND REPAIR

General Trouble shooting hints for the relay PCA are the same as described for the previous versions for the PCA. See Chapter 11 of your M100E/M200E/M400E operator’s manual for more information.

3.1.Removing / Replacing the Relay PCA from the Instrument

The Relay retainer plate installed on the 045230200 PCA (version with AC relays) covers the lower right mounting screw of the relay PCA. Therefore, when removing the relay PCA, the retainer plate must be removed first.

Mounting

Screws

AC Relay Retain Occludes

Mounting Screw on

P/N 045230200

Figure 3-1: Relay PCA 04523 Mounting Screw Locations

USER NOTES:

05118 Rev B3

Image 21

Contents 9480 CARROLL PARK DRIVE SAN DIEGO, CA USA Toll-free Phone Phone Fax TELEDYNE INSTRUMENTS ADVANCED POLLUTION INSTRUMENTATION T-APIEmail api-sales@teledyne.com Relay PCA P/NTHIS PAGE INTENTIONALLY BLANK subassemblies while the unit is under power SAFETY MESSAGESContacting Teledyne Instruments’ Customer Service Department at or Relay PCAAddendum to E-Series Operator Manuals TABLE OF CONTENTS LIST OF FIGURESLIST OF TABLES Relay PCA Table 1-1 List of Analyzers Using New Relay PCA P/N04523 1. INTRODUCTION1.1. What’s the Same 1.2. What’s Different 1.3. Relay PCA Location and LayoutFigure 1-1 Relay PCA Layout P/N04523 1.3.1. Version Figure 1-3 Relay PCA P/N 045230100 with Safety Shield In Place1.3.2. Version Figure 1-2 Relay PCA P/N 045230200 with AC Relay Retainer In PlaceUSER NOTES 2.1. Power Distribution 2. OPERATION AND CONFIGURATION2.1.1. AC Power Configuration Figure 2-1 Power Distribution Block DiagramIZS Permeation Tube Heater and O2 Sensor Connection optional Figure 2-2 Location of AC power Configuration JumpersAC Power Configuration for Internal Pumps JP7 2.1.1.1. AC configuration - Internal Pump JP7Figure 2-3 Pump AC Power Jumpers JP7 110 VAC /115 VACTable 2-2 Power Configuration for Standard AC Heaters JP2 2.1.1.2. AC Configuration - Standard Heaters JP2Figure 2-4 Typical Set Up of AC Heater Jumper Set JP2 1 toTable 2-3 Power Configuration for Optional AC Heaters JP6 2.1.1.3. AC Configuration -Heaters for Option Packages JP6Figure 2-5 Typical Set Up of AC Heater Jumper Set JP2 2.2. Valve Control2.3. Status LEDs & Watch Dog Circuitry 2.3.1. Watchdog Indicator D1D1 RED Figure 2-6 Status LED Locations - Relay PCA2.4. Heater Control Loop Figure 2-7 Heater Control Loop Block DiagramThemocouples MOTHER BOARDTable 2-4 Thermocouple Configuration Jumper JP5 Pin-Outs 2.4.1. Thermocouple Inputs and Configuration Jumper JP5Type J Compensation Type K CompensationINPUT TC1 J15 Figure 2-8 Thermocouple Configuration Jumper JP5 Pin-OutsOutput Scale Selector 7 Type J Compensation 8DC Power Test Point and Wiring Color Code 2.5. DC Power Supply Test PointsTable 2-6 DC Power Supply Acceptable Levels FROM3.1. Removing / Replacing the Relay PCA from the Instrument 3. TROUBLE SHOOTING AND REPAIRMounting Screws Figure 3-1 Relay PCA 04523 Mounting Screw LocationsTable 4-2 List of Included Electronic Schematics 4. SCHEMATICS AND SPARE PARTS FOR RELAY PCA P/NList of Spare Parts DOCUMENT #