Teledyne M100E INPUT TC1 J15, Output Scale Selector 7, Type J Compensation 8, Input Gain Selector

Page 19

Input Gain Selector

Relay PCA 04523

Addendum to E-Series Operator Manuals

Input Gain Selector	Output Scale Selector	Type J Compensation	Type J Compensation	Termination Selector	Input Gain Selector
1 – 11	2 – 12	3 – 13	4 – 14	5 – 15	6 – 16

Output Scale Selector 7 – 17

Type J Compensation 8 – 18

Type J Compensation 9 – 19

Termination Selector 10 – 20

TC1

TC2

Figure 2-8: Thermocouple Configuration Jumper (JP5) Pin-Outs

Table 2-5: Typical Thermocouple Settings for M100E/M200E series analyzers

	TC	TERMINATION	OUTPUT	JUMPER		JUMPER
			SCALE	BETWEE	USED ON
	TYPE	TYPE				COLOR
			TYPE	N PINS

INPUT TC1 (J15)

K	GROUNDED	5mV / °C	2 – 12	M100EH with Mini HiCon Converter	BROWN
			4 – 14

K			2 – 12
K	ISOLATED	5mV / °C	4 – 14	M100EH with Mini HiCon Converter	GREY
			5 – 15


K	ISOLATED	10mV / °C	4 – 14	M100E/M200E with Moly Converter	PURPLE
			5 – 15

J			1 – 11
J	ISOLATED	10mV / °C	3 – 13	M100E/M200E with Moly Converter	RED
			5 – 15

J	GROUNDED	10mV / °C	1 – 11	M100E/M200E with Moly Converter	GREEN
			3 – 13

05118 Rev B3

13

Image 19

Contents Relay PCA P/N TELEDYNE INSTRUMENTS ADVANCED POLLUTION INSTRUMENTATION T-API9480 CARROLL PARK DRIVE SAN DIEGO, CA USA Toll-free Phone Phone Fax Email api-sales@teledyne.comTHIS PAGE INTENTIONALLY BLANK Relay PCA SAFETY MESSAGESsubassemblies while the unit is under power Contacting Teledyne Instruments’ Customer Service Department at orAddendum to E-Series Operator Manuals LIST OF FIGURES TABLE OF CONTENTSLIST OF TABLES Addendum to E-Series Operator Manuals 1. INTRODUCTION Table 1-1 List of Analyzers Using New Relay PCA P/N045231.1. What’s the Same 1.3. Relay PCA Location and Layout 1.2. What’s DifferentFigure 1-1 Relay PCA Layout P/N04523 Figure 1-2 Relay PCA P/N 045230200 with AC Relay Retainer In Place Figure 1-3 Relay PCA P/N 045230100 with Safety Shield In Place1.3.1. Version 1.3.2. VersionUSER NOTES Figure 2-1 Power Distribution Block Diagram 2. OPERATION AND CONFIGURATION2.1. Power Distribution 2.1.1. AC Power ConfigurationIZS Permeation Tube Heater and O2 Sensor Connection optional Figure 2-2 Location of AC power Configuration Jumpers110 VAC /115 VAC 2.1.1.1. AC configuration - Internal Pump JP7AC Power Configuration for Internal Pumps JP7 Figure 2-3 Pump AC Power Jumpers JP71 to 2.1.1.2. AC Configuration - Standard Heaters JP2Table 2-2 Power Configuration for Standard AC Heaters JP2 Figure 2-4 Typical Set Up of AC Heater Jumper Set JP22.2. Valve Control 2.1.1.3. AC Configuration -Heaters for Option Packages JP6Table 2-3 Power Configuration for Optional AC Heaters JP6 Figure 2-5 Typical Set Up of AC Heater Jumper Set JP2Figure 2-6 Status LED Locations - Relay PCA 2.3.1. Watchdog Indicator D12.3. Status LEDs & Watch Dog Circuitry D1 REDMOTHER BOARD Figure 2-7 Heater Control Loop Block Diagram2.4. Heater Control Loop ThemocouplesType K Compensation 2.4.1. Thermocouple Inputs and Configuration Jumper JP5Table 2-4 Thermocouple Configuration Jumper JP5 Pin-Outs Type J CompensationType J Compensation 8 Figure 2-8 Thermocouple Configuration Jumper JP5 Pin-OutsINPUT TC1 J15 Output Scale Selector 7FROM 2.5. DC Power Supply Test PointsDC Power Test Point and Wiring Color Code Table 2-6 DC Power Supply Acceptable LevelsFigure 3-1 Relay PCA 04523 Mounting Screw Locations 3. TROUBLE SHOOTING AND REPAIR3.1. Removing / Replacing the Relay PCA from the Instrument Mounting ScrewsDOCUMENT # 4. SCHEMATICS AND SPARE PARTS FOR RELAY PCA P/NTable 4-2 List of Included Electronic Schematics List of Spare Parts