Teledyne
M200E and M400E, M100E
manual
This Page Intentionally Blank, Relay PCA, Rev B3
Troubleshooting
Watchdog Indicator D1
Operation And Configuration
Jumper Between Pins
Safety
Page 4
Addendum to
E-Series
Operator Manuals
Relay PCA 04523
THIS PAGE INTENTIONALLY BLANK
ii
05118 Rev B3
Page 3
Page 5
Image 4
Page 3
Page 5
Contents
TELEDYNE INSTRUMENTS ADVANCED POLLUTION INSTRUMENTATION T-API
9480 CARROLL PARK DRIVE SAN DIEGO, CA USA Toll-free Phone Phone Fax
Email api-sales@teledyne.com
Relay PCA P/N
THIS PAGE INTENTIONALLY BLANK
SAFETY MESSAGES
subassemblies while the unit is under power
Contacting Teledyne Instruments’ Customer Service Department at or
Relay PCA
Addendum to E-Series Operator Manuals
LIST OF FIGURES
TABLE OF CONTENTS
LIST OF TABLES
THIS PAGE INTENTIONALLY BLANK
1. INTRODUCTION
Table 1-1 List of Analyzers Using New Relay PCA P/N04523
1.1. What’s the Same
1.3. Relay PCA Location and Layout
1.2. What’s Different
Figure 1-1 Relay PCA Layout P/N04523
Figure 1-3 Relay PCA P/N 045230100 with Safety Shield In Place
1.3.1. Version
1.3.2. Version
Figure 1-2 Relay PCA P/N 045230200 with AC Relay Retainer In Place
USER NOTES
2. OPERATION AND CONFIGURATION
2.1. Power Distribution
2.1.1. AC Power Configuration
Figure 2-1 Power Distribution Block Diagram
Figure 2-2 Location of AC power Configuration Jumpers
IZS Permeation Tube Heater and O2 Sensor Connection optional
2.1.1.1. AC configuration - Internal Pump JP7
AC Power Configuration for Internal Pumps JP7
Figure 2-3 Pump AC Power Jumpers JP7
110 VAC /115 VAC
2.1.1.2. AC Configuration - Standard Heaters JP2
Table 2-2 Power Configuration for Standard AC Heaters JP2
Figure 2-4 Typical Set Up of AC Heater Jumper Set JP2
1 to
2.1.1.3. AC Configuration -Heaters for Option Packages JP6
Table 2-3 Power Configuration for Optional AC Heaters JP6
Figure 2-5 Typical Set Up of AC Heater Jumper Set JP2
2.2. Valve Control
2.3.1. Watchdog Indicator D1
2.3. Status LEDs & Watch Dog Circuitry
D1 RED
Figure 2-6 Status LED Locations - Relay PCA
Figure 2-7 Heater Control Loop Block Diagram
2.4. Heater Control Loop
Themocouples
MOTHER BOARD
2.4.1. Thermocouple Inputs and Configuration Jumper JP5
Table 2-4 Thermocouple Configuration Jumper JP5 Pin-Outs
Type J Compensation
Type K Compensation
Figure 2-8 Thermocouple Configuration Jumper JP5 Pin-Outs
INPUT TC1 J15
Output Scale Selector 7
Type J Compensation 8
2.5. DC Power Supply Test Points
DC Power Test Point and Wiring Color Code
Table 2-6 DC Power Supply Acceptable Levels
FROM
3. TROUBLE SHOOTING AND REPAIR
3.1. Removing / Replacing the Relay PCA from the Instrument
Mounting Screws
Figure 3-1 Relay PCA 04523 Mounting Screw Locations
4. SCHEMATICS AND SPARE PARTS FOR RELAY PCA P/N
Table 4-2 List of Included Electronic Schematics
List of Spare Parts
DOCUMENT #
Related pages
What are the specifications listed in the
Line 6 XD-V75 manual
?
Top
Page
Image
Contents