Furuno SC-120 manual Installing the Display Unit, Adjusting for orientation error

Page 28

2. INSTALLATION

2.3.4Adjusting for orientation error

It may be impossible to perfectly align the processor unit on the fore-and-aft or port-and-starboard line. Open the top cover, loosen the two fixing screws on the angular rate sensor and turn. For example, if the orientation error is 2.5° to port, rotate the sensor 2.5° starboard. The range of adjustment is -45°to +45°. Close the top cover after completing the adjustment.

Fore-aft line or Port-starboard

direction

Reference

Direction

Processor Unit

Alignment hole on processor unit

Scale, every 2.5

Bulkhead Mounting

Plate

Fixing Screw

Angular rate sensor, top view

2.4Installing the Display Unit

2.4.1Desktop, overhead mounting

1.Fasten the hanger to the mounting location with four tapping screws (supplied). See the outline drawing for mounting dimensions.

2.Screw the knobs into the display unit.

3.Set display unit to the hanger and tighten the knobs.

4.Run the ground wire between the ground terminal on the display unit and the ship’s superstructure.

DesktopOverhead

Display unit mounting methods

2-14

Image 28

Contents Satellite Compass 00080919206 Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiForeword FeaturesWord to the Owner of the SC-120 System Configuration System configurationEquipment List Name Type Code No Qty RemarksSoftware Version List ViiThis page is intentionally left blank Specifications of Satellite Compass SC-120Power Supply Principle of Operation Principle of satellite compass operationThis page is intentionally left blank Mounting Considerations InstallationSC-series antenna unit Separation degrees Mast diameter Separation distance minimumAntenna and field of view Example of improper installation Example of improper installationDisplay unit, processor unit Installing the Antenna Units Installation postFastening antenna unit to a post Coating bolt, nut and washer with silicone rubberAntenna element Dgps antenna unit Mounting the Dgps antennaCable connection when using cable RG-10UY Waterproofing the extension connectorAntenna cable set Type OP08-17, Code No Deck mount Installing the Processor UnitProcessor unit orientation, deck mounting Processor unit, top view Bulkhead mountAngular rate sensor, top view HEAD1HEAD2HEAD3 Installation of processor unit on the underside of a desk Installation on the underside of a deskProcessor unit orientation, bulkhead mounting Processor Unit, rear view Installing the Display Unit Adjusting for orientation errorDesktop, overhead mounting Display unit mounting methodsFlush mounting Flush mount FName Type Flush mount SGeneral wiring diagram WiringAntenna TPPX6-3D2V-15M Port on Sectional view of coaxial cable 3D2V How to attach connector N-P-8DFB How to attach connector N-P-8DFBInitial Settings Installation setup menuConfirming satellite status choosing mounting method Main menuHeading setup menu Adjusting antenna orientationChoosing heading source Jumper wire and format on the circuit board 20P8171 Port Format Setting RemarksHeading data format Processor unit, cover opened, top viewInstalling the Dgps Beacon Receiver Kit Connection of External EquipmentProcedure Processor unit, cover removed, top viewJ56 Controls OperationDisplay unit Processor unit Turning the Power On/OffPress the DIM key Choosing a Display Description of displaysHeading display Nav data displaySteering display Compass displayROT Rate-of-Turn display Set and Drift display, Distance Run displayAlarms Main menu 2. Choose Alarms and press the ENT keyAlarm menu Alarm menu, GPS buzzer optionsConfirming Satellite Status Alarm menu, Dgps buzzer optionsSatellite status display Displaying the GPS setup menu GPS SetupGPS Setup menu description Output Data HeadingNavigation data InterfaceNAV OUT menu Format selection windowLog pulse Talker identifier mnemonicsLog pulse rate selection window Heading talker selection windowSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Dgps Setup Demonstration modeManual Dgps setup Dgps menuINT Beacon receiver selection windowBeacon station display Programming user beacon stationsStation User display NEW User Channel display Editing user beacon stationsDisplay for editing user channels Erasing all user beacon stations Erasing individual user stationsPrompt for erasure of all user channels Others Menu Others menuResetting Distance Run Reset Distance promptTrip Menu Trip menuThis page is intentionally left blank Preventive Maintenance MAINTENANCE, TroubleshootingDo not open the equipment Troubleshooting DiagnosticsSymptom Cause Remedy Diagnostic test1MAINTENANCE, Troubleshooting Diagnostic test sequenceDiagnostic test2 TEST2 displayProgram Number Clearing DataProgram version no. display Prompts for erasure of dataReplacement of Battery Battery Location Type Code NoBattery exchange options Prompt for exchanging batteryReplacement of Fuse Error MessagesError Message Meaning Remedy Message displayError messages con’t from previous BattteryAppendix Menu TreeGeodetic Chart Codes North AmericanDigital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rollingHDM- Heading magnetic VDR Set and drift VTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output PortsParts Location Processor unit, cover removedParts List R U N OＰａｃｋｉｎｇＬｉｓｔ SC-1203F 工事材料表 Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Index Index-1