Furuno SC-120 Programming user beacon stations, Beacon station display, Station User display

Page 53

3. OPERATION

LIST

a)The following display appears after pressing the [ENT] key at step 7.

STATION (NEAREST)

[EXIT]

[USER]

 

 

310.0

 

29.1 nm

92

 

287.0

 

56.7 nm

134

 

292.0

 

160 nm

320

 

321.0

 

234 nm

134

 

302.0

 

426 nm

121

*

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Beacon station frequency

* = User-registered station

Range and bearing from own ship to beacon station (Reference only)

Beacon station display

b)Choose desired station with the Omnipad.

c)Press the [ENT] key.

8.Press the [DISP] key to close the menu.

3.10.2Programming user beacon stations

The user may program 20 DGPS beacon stations from which to use in selection of DGPS beacon station. Whenever a new station comes into operation, you can add it to the list.

1.Press the [MENU] key to open the menu.

2.Choose DGPS and press the [ENT] key.

3.Choose STATION and press the [ENT] key.

4.Choose LIST and press the [ENT] key.

5.Choose USER and press the [ENT] key to show the STATION (USER) display.

STATION (USER)

[EXIT] [NEW?] [CLR?] 01 02 03 04 05 06

STATION (USER) display

6. Choose “NEW?” and press the [ENT] key.

3-15

Image 53
Contents Satellite Compass 00080919206 Safety Instructions Table of Contents Iii MAINTENANCE, TroubleshootingWord to the Owner of the SC-120 FeaturesForeword System configuration System ConfigurationName Type Code No Qty Remarks Equipment ListVii Software Version ListThis page is intentionally left blank SC-120 Specifications of Satellite CompassPower Supply Principle of satellite compass operation Principle of OperationThis page is intentionally left blank SC-series antenna unit InstallationMounting Considerations Antenna and field of view Mast diameter Separation distance minimumSeparation degrees Display unit, processor unit Example of improper installationExample of improper installation Installation post Installing the Antenna UnitsCoating bolt, nut and washer with silicone rubber Fastening antenna unit to a postAntenna element Mounting the Dgps antenna Dgps antenna unitAntenna cable set Type OP08-17, Code No Waterproofing the extension connectorCable connection when using cable RG-10UY Processor unit orientation, deck mounting Installing the Processor UnitDeck mount Angular rate sensor, top view Bulkhead mountProcessor unit, top view HEAD1HEAD2HEAD3 Processor unit orientation, bulkhead mounting Installation on the underside of a deskInstallation of processor unit on the underside of a desk Processor Unit, rear view Adjusting for orientation error Installing the Display UnitDesktop, overhead mounting Display unit mounting methodsFlush mount F Flush mountingName Type Flush mount SAntenna TPPX6-3D2V-15M Port on WiringGeneral wiring diagram Sectional view of coaxial cable 3D2V How to attach connector N-P-8DFB How to attach connector N-P-8DFBInstallation setup menu Initial SettingsConfirming satellite status choosing mounting method Main menuChoosing heading source Adjusting antenna orientationHeading setup menu Port Format Setting Remarks Jumper wire and format on the circuit board 20P8171Heading data format Processor unit, cover opened, top viewConnection of External Equipment Installing the Dgps Beacon Receiver KitProcessor unit, cover removed, top view ProcedureJ56 Display unit OperationControls Press the DIM key Turning the Power On/OffProcessor unit Description of displays Choosing a DisplayHeading display Nav data displayCompass display Steering displayROT Rate-of-Turn display Set and Drift display, Distance Run displayMain menu 2. Choose Alarms and press the ENT key AlarmsAlarm menu Alarm menu, GPS buzzer optionsSatellite status display Alarm menu, Dgps buzzer optionsConfirming Satellite Status GPS Setup menu description GPS SetupDisplaying the GPS setup menu Heading Output DataInterface Navigation dataNAV OUT menu Format selection windowTalker identifier mnemonics Log pulseLog pulse rate selection window Heading talker selection windowGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Demonstration mode Dgps SetupManual Dgps setup Dgps menuBeacon receiver selection window INTStation User display Programming user beacon stationsBeacon station display Display for editing user channels Editing user beacon stationsNEW User Channel display Prompt for erasure of all user channels Erasing individual user stationsErasing all user beacon stations Others menu Others MenuReset Distance prompt Resetting Distance RunTrip Menu Trip menuThis page is intentionally left blank Do not open the equipment MAINTENANCE, TroubleshootingPreventive Maintenance Diagnostics TroubleshootingSymptom Cause Remedy Diagnostic test1Diagnostic test sequence MAINTENANCE, TroubleshootingTEST2 display Diagnostic test2Clearing Data Program NumberProgram version no. display Prompts for erasure of dataBattery Location Type Code No Replacement of BatteryBattery exchange options Prompt for exchanging batteryError Messages Replacement of FuseError Message Meaning Remedy Message displayBatttery Error messages con’t from previousMenu Tree AppendixNorth American Geodetic Chart CodesDigital Interface Schematic diagrams NAV OUT1 Port PFECatt- True heading, pitching, rolling Data sentencesHDM- Heading magnetic VDR Set and drift VTG Course over ground and ground speed Input/Output Ports Port Label Connector Signal Remarks TypeProcessor unit, cover removed Parts LocationR U N O Parts ListPacking List SC-1203F 工事材料表 Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Index-1 Index