Furuno SC-120 manual Procedure, Processor unit, cover removed, top view

Page 37

2. INSTALLATION

Procedure

1.Open the top cover processor unit.

2.Open the cover of the DGPS receiver assembly.

3.Connect the cable TNCBPJ(140) to J1 on the DGPS receiver assembly.

4.Remove the plug at the rear of the processor unit.

5.Pass the cable TNCBPJ(140) through the hole made at step 4 and fasten it with the toothed washer and nut.

6.Fasten the DGPS receiver assembly at the location shown below.

Panhead Screw
M3X8, 2 pcs.
DGPS Receiver
Assembly	J2	Cover
	J2
	J1
Cable Assembly
TNCBPJ(140)

Toothed Washer

Nut

Torque

1.37 0.98 Nm

Plug

Processor unit, cover removed, top view

7.Connect the 6P connector of the PH connector 20-061(7-6P) to J2 on the DGPS receiver assy.

8.Connector the 7P connector of the PH connector 20-061(7-6P) to J10 on the circuit board 20P8171.

2-23

Image 37

Contents Satellite Compass 00080919206 Safety Instructions Table of Contents Iii MAINTENANCE, TroubleshootingForeword FeaturesWord to the Owner of the SC-120 System configuration System ConfigurationName Type Code No Qty Remarks Equipment ListVii Software Version ListThis page is intentionally left blank SC-120 Specifications of Satellite CompassPower Supply Principle of satellite compass operation Principle of OperationThis page is intentionally left blank Mounting Considerations InstallationSC-series antenna unit Separation degrees Mast diameter Separation distance minimumAntenna and field of view Example of improper installation Example of improper installationDisplay unit, processor unit Installation post Installing the Antenna UnitsCoating bolt, nut and washer with silicone rubber Fastening antenna unit to a postAntenna element Mounting the Dgps antenna Dgps antenna unitCable connection when using cable RG-10UY Waterproofing the extension connectorAntenna cable set Type OP08-17, Code No Deck mount Installing the Processor UnitProcessor unit orientation, deck mounting Processor unit, top view Bulkhead mountAngular rate sensor, top view HEAD1HEAD2HEAD3 Installation of processor unit on the underside of a desk Installation on the underside of a deskProcessor unit orientation, bulkhead mounting Processor Unit, rear view Adjusting for orientation error Installing the Display UnitDesktop, overhead mounting Display unit mounting methodsFlush mount F Flush mountingName Type Flush mount SGeneral wiring diagram WiringAntenna TPPX6-3D2V-15M Port on Sectional view of coaxial cable 3D2V How to attach connector N-P-8DFB How to attach connector N-P-8DFBInstallation setup menu Initial SettingsConfirming satellite status choosing mounting method Main menuHeading setup menu Adjusting antenna orientationChoosing heading source Port Format Setting Remarks Jumper wire and format on the circuit board 20P8171Heading data format Processor unit, cover opened, top viewConnection of External Equipment Installing the Dgps Beacon Receiver KitProcessor unit, cover removed, top view ProcedureJ56 Controls OperationDisplay unit Processor unit Turning the Power On/OffPress the DIM key Description of displays Choosing a DisplayHeading display Nav data displayCompass display Steering displayROT Rate-of-Turn display Set and Drift display, Distance Run displayMain menu 2. Choose Alarms and press the ENT key AlarmsAlarm menu Alarm menu, GPS buzzer optionsConfirming Satellite Status Alarm menu, Dgps buzzer optionsSatellite status display Displaying the GPS setup menu GPS SetupGPS Setup menu description Heading Output DataInterface Navigation dataNAV OUT menu Format selection windowTalker identifier mnemonics Log pulseLog pulse rate selection window Heading talker selection windowSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Demonstration mode Dgps SetupManual Dgps setup Dgps menuBeacon receiver selection window INTBeacon station display Programming user beacon stationsStation User display NEW User Channel display Editing user beacon stationsDisplay for editing user channels Erasing all user beacon stations Erasing individual user stationsPrompt for erasure of all user channels Others menu Others MenuReset Distance prompt Resetting Distance RunTrip Menu Trip menuThis page is intentionally left blank Preventive Maintenance MAINTENANCE, TroubleshootingDo not open the equipment Diagnostics TroubleshootingSymptom Cause Remedy Diagnostic test1Diagnostic test sequence MAINTENANCE, TroubleshootingTEST2 display Diagnostic test2Clearing Data Program NumberProgram version no. display Prompts for erasure of dataBattery Location Type Code No Replacement of BatteryBattery exchange options Prompt for exchanging batteryError Messages Replacement of FuseError Message Meaning Remedy Message displayBatttery Error messages con’t from previousMenu Tree AppendixNorth American Geodetic Chart CodesDigital Interface Schematic diagrams NAV OUT1 Port PFECatt- True heading, pitching, rolling Data sentencesHDM- Heading magnetic VDR Set and drift VTG Course over ground and ground speed Input/Output Ports Port Label Connector Signal Remarks TypeProcessor unit, cover removed Parts LocationR U N O Parts ListＰａｃｋｉｎｇＬｉｓｔ SC-1203F 工事材料表 Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Index-1 Index