Furuno SC-120 manual Displaying the GPS setup menu, GPS Setup menu description

Page 45

3. OPERATION

3.7GPS Setup

The GPS SETUP menu smooths position and course, averages speed, applies position offset, and deactivates unhealthy satellites.

3.7.1Displaying the GPS setup menu

1.Press the [MENU] key to open the menu.

2.Choose GPS SETUP and press the [ENT] key.

GPS SETUP

SMOOTH POS

:

 

 

0SEC

SMOOTH S/C

:

 

 

5SEC

LAT OFFSET

:

0.000’N

LON OFFSET

:

0.000’E

DISABLE SV

:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GPS SETUP menu

3.7.2GPS SETUP menu description

SMOOTH POS (Smoothing position)

When the DOP (Dilution of Precision, the index for position-fixing accuracy) or receiving condition is unfavorable, the GPS fix may change randomly, even if the vessel at anchor. This change can be smoothed by averaging a number of GPS fixes. The setting range is from 0 (no smoothing) to 999 seconds. The setting range is from 0 (no smoothing) to 999 seconds, and the default is 5 s, which is good for rolling period o 5-8 s. The higher the setting the more smoothing. However, too high a setting slows updating of position. “0” is the default setting; increase the setting if the GPS fix fluctuates largely.

SMOOTH S/C (Smoothing speed/course)

Ship’s speed and course are directly measured by receiving GPS satellite signals, independent of positions. The data varies with receiving conditions and other factors. You can reduce this random variation by increasing the smoothing. The higher the setting the more that speed and course are smoothed. If the setting is too high, however, the follow-up to actual values gets slower. The setting range is from 0 (no smoothing) to 999 seconds.

LAT/LON OFFSET (L/L position offset)

If GPS fixes are erroneous while at anchor, enter a position offset to compensate for position error. Consult a nautical chart to determine latitude and longitude differences between the chart and GPS display. Enter that value as the offset.

DISABLE SV (Disable satellite)

Every GPS satellite is broadcasting abnormal satellite number(s) in its Almanac, which contains general orbital data about all GPS satellites. Using this

3-7

Image 45
Contents Satellite Compass 00080919206 Safety Instructions Table of Contents Iii MAINTENANCE, TroubleshootingFeatures ForewordWord to the Owner of the SC-120 System configuration System ConfigurationName Type Code No Qty Remarks Equipment ListVii Software Version ListThis page is intentionally left blank SC-120 Specifications of Satellite CompassPower Supply Principle of satellite compass operation Principle of OperationThis page is intentionally left blank Installation Mounting ConsiderationsSC-series antenna unit Mast diameter Separation distance minimum Separation degreesAntenna and field of view Example of improper installation Example of improper installationDisplay unit, processor unit Installation post Installing the Antenna UnitsCoating bolt, nut and washer with silicone rubber Fastening antenna unit to a postAntenna element Mounting the Dgps antenna Dgps antenna unitWaterproofing the extension connector Cable connection when using cable RG-10UYAntenna cable set Type OP08-17, Code No Installing the Processor Unit Deck mountProcessor unit orientation, deck mounting Bulkhead mount Processor unit, top viewAngular rate sensor, top view HEAD1HEAD2HEAD3 Installation on the underside of a desk Installation of processor unit on the underside of a deskProcessor unit orientation, bulkhead mounting Processor Unit, rear view Adjusting for orientation error Installing the Display UnitDesktop, overhead mounting Display unit mounting methodsFlush mount F Flush mountingName Type Flush mount SWiring General wiring diagramAntenna TPPX6-3D2V-15M Port on Sectional view of coaxial cable 3D2V How to attach connector N-P-8DFB How to attach connector N-P-8DFBInstallation setup menu Initial SettingsConfirming satellite status choosing mounting method Main menuAdjusting antenna orientation Heading setup menuChoosing heading source Port Format Setting Remarks Jumper wire and format on the circuit board 20P8171Heading data format Processor unit, cover opened, top viewConnection of External Equipment Installing the Dgps Beacon Receiver KitProcessor unit, cover removed, top view ProcedureJ56 Operation ControlsDisplay unit Turning the Power On/Off Processor unitPress the DIM key Description of displays Choosing a DisplayHeading display Nav data displayCompass display Steering displayROT Rate-of-Turn display Set and Drift display, Distance Run displayMain menu 2. Choose Alarms and press the ENT key AlarmsAlarm menu Alarm menu, GPS buzzer optionsAlarm menu, Dgps buzzer options Confirming Satellite StatusSatellite status display GPS Setup Displaying the GPS setup menuGPS Setup menu description Heading Output DataInterface Navigation dataNAV OUT menu Format selection windowTalker identifier mnemonics Log pulseLog pulse rate selection window Heading talker selection windowSystem Setup System Setup menuGeodetic data Using local time Units of measurementTime format Demonstration mode Dgps SetupManual Dgps setup Dgps menuBeacon receiver selection window INTProgramming user beacon stations Beacon station displayStation User display Editing user beacon stations NEW User Channel displayDisplay for editing user channels Erasing individual user stations Erasing all user beacon stationsPrompt for erasure of all user channels Others menu Others MenuReset Distance prompt Resetting Distance RunTrip Menu Trip menuThis page is intentionally left blank MAINTENANCE, Troubleshooting Preventive MaintenanceDo not open the equipment Diagnostics TroubleshootingSymptom Cause Remedy Diagnostic test1Diagnostic test sequence MAINTENANCE, TroubleshootingTEST2 display Diagnostic test2Clearing Data Program NumberProgram version no. display Prompts for erasure of dataBattery Location Type Code No Replacement of BatteryBattery exchange options Prompt for exchanging batteryError Messages Replacement of FuseError Message Meaning Remedy Message displayBatttery Error messages con’t from previousMenu Tree AppendixNorth American Geodetic Chart CodesDigital Interface Schematic diagrams NAV OUT1 Port PFECatt- True heading, pitching, rolling Data sentencesHDM- Heading magnetic VDR Set and drift VTG Course over ground and ground speed Input/Output Ports Port Label Connector Signal Remarks TypeProcessor unit, cover removed Parts LocationR U N O Parts ListPacking List SC-1203F 工事材料表 Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Index-1 Index