Furuno SC-120 manual Antenna element

Page 20

2.INSTALLATION

4.As shown below, make a loop in the antenna cable and fasten the antenna cable to the antenna post with two cable ties.

Coat bolt threads with Three Bond. Fasten bolt

with nuts and then coat nuts with Three Bond also.

Coat with Three Bond 1211 (supplied).

Fix antenna cable.

5.

Coat bolt threads with

 

 

Three Bond 1211.

Bird-repellent fixture

 

Fasten bolts with nuts.

 

 

Coat nuts at the

 

 

bottom of each

 

 

antenna element with

 

 

Three Bond 1211.

 

6.

Paint post and support

 

 

plate with

 

 

anti-corrosive paint.

 

7.

Attach “bird-repellent

 

 

fixtures” (supplied) to

 

 

each antenna element

 

 

and center cover as shown right.

Antenna element

2-6

Image 20
Contents Satellite Compass 00080919206 Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiWord to the Owner of the SC-120 FeaturesForeword System Configuration System configurationEquipment List Name Type Code No Qty RemarksSoftware Version List ViiThis page is intentionally left blank Specifications of Satellite Compass SC-120Power Supply Principle of Operation Principle of satellite compass operationThis page is intentionally left blank SC-series antenna unit InstallationMounting Considerations Antenna and field of view Mast diameter Separation distance minimumSeparation degrees Display unit, processor unit Example of improper installationExample of improper installation Installing the Antenna Units Installation postFastening antenna unit to a post Coating bolt, nut and washer with silicone rubberAntenna element Dgps antenna unit Mounting the Dgps antennaAntenna cable set Type OP08-17, Code No Waterproofing the extension connectorCable connection when using cable RG-10UY Processor unit orientation, deck mounting Installing the Processor UnitDeck mount Angular rate sensor, top view Bulkhead mountProcessor unit, top view HEAD1HEAD2HEAD3 Processor unit orientation, bulkhead mounting Installation on the underside of a deskInstallation of processor unit on the underside of a desk Processor Unit, rear view Installing the Display Unit Adjusting for orientation errorDesktop, overhead mounting Display unit mounting methodsFlush mounting Flush mount FName Type Flush mount SAntenna TPPX6-3D2V-15M Port on WiringGeneral wiring diagram Sectional view of coaxial cable 3D2V How to attach connector N-P-8DFB How to attach connector N-P-8DFBInitial Settings Installation setup menuConfirming satellite status choosing mounting method Main menuChoosing heading source Adjusting antenna orientationHeading setup menu Jumper wire and format on the circuit board 20P8171 Port Format Setting RemarksHeading data format Processor unit, cover opened, top viewInstalling the Dgps Beacon Receiver Kit Connection of External EquipmentProcedure Processor unit, cover removed, top viewJ56 Display unit OperationControls Press the DIM key Turning the Power On/OffProcessor unit Choosing a Display Description of displaysHeading display Nav data displaySteering display Compass displayROT Rate-of-Turn display Set and Drift display, Distance Run displayAlarms Main menu 2. Choose Alarms and press the ENT keyAlarm menu Alarm menu, GPS buzzer optionsSatellite status display Alarm menu, Dgps buzzer optionsConfirming Satellite Status GPS Setup menu description GPS SetupDisplaying the GPS setup menu Output Data HeadingNavigation data InterfaceNAV OUT menu Format selection windowLog pulse Talker identifier mnemonicsLog pulse rate selection window Heading talker selection windowGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Dgps Setup Demonstration modeManual Dgps setup Dgps menuINT Beacon receiver selection windowStation User display Programming user beacon stationsBeacon station display Display for editing user channels Editing user beacon stationsNEW User Channel display Prompt for erasure of all user channels Erasing individual user stationsErasing all user beacon stations Others Menu Others menuResetting Distance Run Reset Distance promptTrip Menu Trip menuThis page is intentionally left blank Do not open the equipment MAINTENANCE, TroubleshootingPreventive Maintenance Troubleshooting DiagnosticsSymptom Cause Remedy Diagnostic test1MAINTENANCE, Troubleshooting Diagnostic test sequenceDiagnostic test2 TEST2 displayProgram Number Clearing DataProgram version no. display Prompts for erasure of dataReplacement of Battery Battery Location Type Code NoBattery exchange options Prompt for exchanging batteryReplacement of Fuse Error MessagesError Message Meaning Remedy Message displayError messages con’t from previous BattteryAppendix Menu TreeGeodetic Chart Codes North AmericanDigital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rollingHDM- Heading magnetic VDR Set and drift VTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output PortsParts Location Processor unit, cover removedParts List R U N OPacking List SC-1203F 工事材料表 Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Index Index-1