Furuno SC-120 manual Diagnostic test2, TEST2 display

Page 62

4. MAINTENANCE, TROUBLESHOOTING

Diagnostic test2

If the heading indication changes randomly when ship is at anchor or does not change when the ship moves, run the test2 following the procedure below, with the ship at anchor and satellite signal received.

Note: Heading is not output during the diagnostic test, and this is communicated with an appropriate message. After completing the diagnostic test, turn the power off and on to update heading data.

1.Press the [MENU] key to open the menu.

2.Choose SYS SETUP and press the [ENT] key.

3.Choose TEST? and press the [ENT] key.

TEST1

TEST2

Test menu options

4. Choose TEST2 and press the [ENT] key.

TEST START?

(STOP: PWR OFF)

ARE YOU SURE?

YES

NO

Test start prompt

5.Press to choose YES and press the [ENT] key.

6.Press the [ENT] key twice. Rate and angle values are 0.0° . If the values increase or decrease markedly (with ship at anchor), suspect rate sensor trouble. Contact your dealer to request service.

TEST2

 

YAN

ROL

PIT

RATE

0.0

0.0

0.0

ANGLE

0.0￿

0.0￿

0.0￿

<STOP: PWR OFF>

TEST2 display

7. Turn off the processor unit to quit the diagnostic test2.

4-4

Image 62
Contents Satellite Compass 00080919206 Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiWord to the Owner of the SC-120 FeaturesForeword System Configuration System configurationEquipment List Name Type Code No Qty RemarksSoftware Version List ViiThis page is intentionally left blank Specifications of Satellite Compass SC-120Power Supply Principle of Operation Principle of satellite compass operationThis page is intentionally left blank SC-series antenna unit InstallationMounting Considerations Antenna and field of view Mast diameter Separation distance minimumSeparation degrees Display unit, processor unit Example of improper installationExample of improper installation Installing the Antenna Units Installation postFastening antenna unit to a post Coating bolt, nut and washer with silicone rubberAntenna element Dgps antenna unit Mounting the Dgps antennaAntenna cable set Type OP08-17, Code No Waterproofing the extension connectorCable connection when using cable RG-10UY Processor unit orientation, deck mounting Installing the Processor UnitDeck mount Angular rate sensor, top view Bulkhead mountProcessor unit, top view HEAD1HEAD2HEAD3 Processor unit orientation, bulkhead mounting Installation on the underside of a deskInstallation of processor unit on the underside of a desk Processor Unit, rear view Desktop, overhead mounting Installing the Display UnitAdjusting for orientation error Display unit mounting methodsName Type Flush mountingFlush mount F Flush mount SAntenna TPPX6-3D2V-15M Port on WiringGeneral wiring diagram Sectional view of coaxial cable 3D2V How to attach connector N-P-8DFB How to attach connector N-P-8DFBConfirming satellite status choosing mounting method Initial SettingsInstallation setup menu Main menuChoosing heading source Adjusting antenna orientationHeading setup menu Heading data format Jumper wire and format on the circuit board 20P8171Port Format Setting Remarks Processor unit, cover opened, top viewInstalling the Dgps Beacon Receiver Kit Connection of External EquipmentProcedure Processor unit, cover removed, top viewJ56 Display unit OperationControls Press the DIM key Turning the Power On/OffProcessor unit Heading display Choosing a DisplayDescription of displays Nav data displayROT Rate-of-Turn display Steering displayCompass display Set and Drift display, Distance Run displayAlarm menu AlarmsMain menu 2. Choose Alarms and press the ENT key Alarm menu, GPS buzzer optionsSatellite status display Alarm menu, Dgps buzzer optionsConfirming Satellite Status GPS Setup menu description GPS SetupDisplaying the GPS setup menu Output Data HeadingNAV OUT menu Navigation dataInterface Format selection windowLog pulse rate selection window Log pulseTalker identifier mnemonics Heading talker selection windowGeodetic data System SetupSystem Setup menu Time format Using local timeUnits of measurement Manual Dgps setup Dgps SetupDemonstration mode Dgps menuINT Beacon receiver selection windowStation User display Programming user beacon stationsBeacon station display Display for editing user channels Editing user beacon stationsNEW User Channel display Prompt for erasure of all user channels Erasing individual user stationsErasing all user beacon stations Others Menu Others menuTrip Menu Resetting Distance RunReset Distance prompt Trip menuThis page is intentionally left blank Do not open the equipment MAINTENANCE, TroubleshootingPreventive Maintenance Symptom Cause Remedy TroubleshootingDiagnostics Diagnostic test1MAINTENANCE, Troubleshooting Diagnostic test sequenceDiagnostic test2 TEST2 displayProgram version no. display Program NumberClearing Data Prompts for erasure of dataBattery exchange options Replacement of BatteryBattery Location Type Code No Prompt for exchanging batteryError Message Meaning Remedy Replacement of FuseError Messages Message displayError messages con’t from previous BattteryAppendix Menu TreeGeodetic Chart Codes North AmericanDigital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rollingHDM- Heading magnetic VDR Set and drift VTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output PortsParts Location Processor unit, cover removedParts List R U N OPacking List SC-1203F 工事材料表 Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Index Index-1