Furuno SC-120 manual Turning the Power On/Off, Processor unit, Press the DIM key

Page 40

3. OPERATION

3.2Turning the Power On/Off

Use the power switch on the processor unit to turn the power on and off.

POWER

Switch

Processor unit

The display starts up with the last-used display.

Note 1: Turn on external equipment AFTER the SC-120 is showing reliable heading data, to prevent heading output error.

Note 2: The display flashes when backup heading data is used.

3.3

Panel Illumination, Display Contrast

 

1. Press the [DIM] key.

CONTRASTDIMMEREXI:[E(1T(0-8)]-63)

 

 

4

 

 

45

Dialog box for adjustment of panel illumination, display contrast

2.Press ▲ or ▼ on the Omnipad to adjust panel illumination.

3.Press or on the Omnipad to adjust display contrast.

4.Press the [ENT] key.

3-2

Image 40
Contents Satellite Compass 00080919206 Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiForeword FeaturesWord to the Owner of the SC-120 System Configuration System configurationEquipment List Name Type Code No Qty RemarksSoftware Version List ViiThis page is intentionally left blank Specifications of Satellite Compass SC-120Power Supply Principle of Operation Principle of satellite compass operationThis page is intentionally left blank Mounting Considerations InstallationSC-series antenna unit Separation degrees Mast diameter Separation distance minimumAntenna and field of view Example of improper installation Example of improper installationDisplay unit, processor unit Installing the Antenna Units Installation postFastening antenna unit to a post Coating bolt, nut and washer with silicone rubberAntenna element Dgps antenna unit Mounting the Dgps antennaCable connection when using cable RG-10UY Waterproofing the extension connectorAntenna cable set Type OP08-17, Code No Deck mount Installing the Processor UnitProcessor unit orientation, deck mounting Processor unit, top view Bulkhead mountAngular rate sensor, top view HEAD1HEAD2HEAD3 Installation of processor unit on the underside of a desk Installation on the underside of a deskProcessor unit orientation, bulkhead mounting Processor Unit, rear view Installing the Display Unit Adjusting for orientation errorDesktop, overhead mounting Display unit mounting methodsFlush mounting Flush mount FName Type Flush mount SGeneral wiring diagram WiringAntenna TPPX6-3D2V-15M Port on Sectional view of coaxial cable 3D2V How to attach connector N-P-8DFB How to attach connector N-P-8DFBInitial Settings Installation setup menuConfirming satellite status choosing mounting method Main menuHeading setup menu Adjusting antenna orientationChoosing heading source Jumper wire and format on the circuit board 20P8171 Port Format Setting RemarksHeading data format Processor unit, cover opened, top viewInstalling the Dgps Beacon Receiver Kit Connection of External EquipmentProcedure Processor unit, cover removed, top viewJ56 Controls OperationDisplay unit Processor unit Turning the Power On/OffPress the DIM key Choosing a Display Description of displaysHeading display Nav data displaySteering display Compass displayROT Rate-of-Turn display Set and Drift display, Distance Run displayAlarms Main menu 2. Choose Alarms and press the ENT keyAlarm menu Alarm menu, GPS buzzer optionsConfirming Satellite Status Alarm menu, Dgps buzzer optionsSatellite status display Displaying the GPS setup menu GPS SetupGPS Setup menu description Output Data HeadingNavigation data InterfaceNAV OUT menu Format selection windowLog pulse Talker identifier mnemonicsLog pulse rate selection window Heading talker selection windowSystem Setup menu System SetupGeodetic data Units of measurement Using local timeTime format Dgps Setup Demonstration modeManual Dgps setup Dgps menuINT Beacon receiver selection windowBeacon station display Programming user beacon stationsStation User display NEW User Channel display Editing user beacon stationsDisplay for editing user channels Erasing all user beacon stations Erasing individual user stationsPrompt for erasure of all user channels Others Menu Others menuResetting Distance Run Reset Distance promptTrip Menu Trip menuThis page is intentionally left blank Preventive Maintenance MAINTENANCE, TroubleshootingDo not open the equipment Troubleshooting DiagnosticsSymptom Cause Remedy Diagnostic test1MAINTENANCE, Troubleshooting Diagnostic test sequenceDiagnostic test2 TEST2 displayProgram Number Clearing DataProgram version no. display Prompts for erasure of dataReplacement of Battery Battery Location Type Code NoBattery exchange options Prompt for exchanging batteryReplacement of Fuse Error MessagesError Message Meaning Remedy Message displayError messages con’t from previous BattteryAppendix Menu TreeGeodetic Chart Codes North AmericanDigital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rollingHDM- Heading magnetic VDR Set and drift VTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output PortsParts Location Processor unit, cover removedParts List R U N OPacking List SC-1203F 工事材料表 Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Index Index-1