Furuno SC-120 manual Editing user beacon stations, NEW User Channel display

Page 54

3. OPERATION

NEW USER CHANNEL

FREQ

:

310.0kHz

RATE

: 200BPS

LAT

: 37˚59’N

LON

: 133˚00’E

EXIT?

SAVE?

NEW USER CHANNEL display

Note: For steps 7-10 use the Omnipad to enter data. Choose location with

or ; change value with ▲ or ▼.

7.Press the [ENT] key, enter frequency of the station, and press the [ENT] key.

8.Press the [ENT] key, enter baud rate of the station, and press the [ENT] key.

9.Press the [ENT] key, enter latitude of the station, and press the [ENT] key.

10.Press the [ENT] key, enter longitude of the station, and press the [ENT] key.

11.Choose “SAVE?” and press the [ENT] key.

12.Press the [DISP] key to close the menu.

3.10.3Editing user beacon stations

1.Press the [MENU] key to open the menu.

2.Choose DGPS and press the [ENT] key.

3.Choose STATION and press the [ENT] key.

4.Choose LIST and press the [ENT] key.

5.Choose USER and press the [ENT] key.

6.Choose a station from the list and press the [ENT] key. The display looks something like the one below.

FREQ

:

310.0kHz

RATE

: 200BPS

LAT

: 37˚59’N

LON

: 133˚00’E

EXIT SAVE? ERASE?

Display for editing user channels

7.Choose item, press the [ENT] key, edit data, and press the [ENT] key.

8.Choose “SAVE?” and press the [ENT] key.

9.Press the [MENU] key twice to finish.

3-16

Image 54
Contents Satellite Compass 00080919206 Safety Instructions Table of Contents MAINTENANCE, Troubleshooting IiiFeatures ForewordWord to the Owner of the SC-120 System Configuration System configurationEquipment List Name Type Code No Qty RemarksSoftware Version List ViiThis page is intentionally left blank Specifications of Satellite Compass SC-120Power Supply Principle of Operation Principle of satellite compass operationThis page is intentionally left blank Installation Mounting ConsiderationsSC-series antenna unit Mast diameter Separation distance minimum Separation degreesAntenna and field of view Example of improper installation Example of improper installationDisplay unit, processor unit Installing the Antenna Units Installation postFastening antenna unit to a post Coating bolt, nut and washer with silicone rubberAntenna element Dgps antenna unit Mounting the Dgps antennaWaterproofing the extension connector Cable connection when using cable RG-10UYAntenna cable set Type OP08-17, Code No Installing the Processor Unit Deck mountProcessor unit orientation, deck mounting Bulkhead mount Processor unit, top viewAngular rate sensor, top view HEAD1HEAD2HEAD3 Installation on the underside of a desk Installation of processor unit on the underside of a deskProcessor unit orientation, bulkhead mounting Processor Unit, rear view Desktop, overhead mounting Installing the Display UnitAdjusting for orientation error Display unit mounting methodsName Type Flush mountingFlush mount F Flush mount SWiring General wiring diagramAntenna TPPX6-3D2V-15M Port on Sectional view of coaxial cable 3D2V How to attach connector N-P-8DFB How to attach connector N-P-8DFBConfirming satellite status choosing mounting method Initial SettingsInstallation setup menu Main menuAdjusting antenna orientation Heading setup menuChoosing heading source Heading data format Jumper wire and format on the circuit board 20P8171Port Format Setting Remarks Processor unit, cover opened, top viewInstalling the Dgps Beacon Receiver Kit Connection of External EquipmentProcedure Processor unit, cover removed, top viewJ56 Operation ControlsDisplay unit Turning the Power On/Off Processor unitPress the DIM key Heading display Choosing a DisplayDescription of displays Nav data displayROT Rate-of-Turn display Steering displayCompass display Set and Drift display, Distance Run displayAlarm menu AlarmsMain menu 2. Choose Alarms and press the ENT key Alarm menu, GPS buzzer optionsAlarm menu, Dgps buzzer options Confirming Satellite StatusSatellite status display GPS Setup Displaying the GPS setup menuGPS Setup menu description Output Data HeadingNAV OUT menu Navigation dataInterface Format selection windowLog pulse rate selection window Log pulseTalker identifier mnemonics Heading talker selection windowSystem Setup System Setup menuGeodetic data Using local time Units of measurementTime format Manual Dgps setup Dgps SetupDemonstration mode Dgps menuINT Beacon receiver selection windowProgramming user beacon stations Beacon station displayStation User display Editing user beacon stations NEW User Channel displayDisplay for editing user channels Erasing individual user stations Erasing all user beacon stationsPrompt for erasure of all user channels Others Menu Others menuTrip Menu Resetting Distance RunReset Distance prompt Trip menuThis page is intentionally left blank MAINTENANCE, Troubleshooting Preventive MaintenanceDo not open the equipment Symptom Cause Remedy TroubleshootingDiagnostics Diagnostic test1MAINTENANCE, Troubleshooting Diagnostic test sequenceDiagnostic test2 TEST2 displayProgram version no. display Program NumberClearing Data Prompts for erasure of dataBattery exchange options Replacement of BatteryBattery Location Type Code No Prompt for exchanging batteryError Message Meaning Remedy Replacement of FuseError Messages Message displayError messages con’t from previous BattteryAppendix Menu TreeGeodetic Chart Codes North AmericanDigital Interface Schematic diagrams NAV OUT1 Port Data sentences PFECatt- True heading, pitching, rollingHDM- Heading magnetic VDR Set and drift VTG Course over ground and ground speed Port Label Connector Signal Remarks Type Input/Output PortsParts Location Processor unit, cover removedParts List R U N OPacking List SC-1203F 工事材料表 Page Page Page GP-1850,GP-1650,FA-100,GP-1640/F SC-60/120,GD/GP-280/680/380 20AG-X-9405 Page Page Page Page Page Page Page Page Index Index-1