INSTALLATION
SYSTEM WIRING
REFER TO AND FOLLOW THE APPLIANCE MANUFACTURER'S WIRING DIAGRAM. REFER TO FIGURES 3 AND 4 FOR TERMINAL IDENTIFICATION.
4.693” Inlet to Outlet
NOTE
All wiring should be installed according to local and national electrical codes and ordinances.
Always check that the electrical power supply used agrees with the voltage and frequency shown on the gas control.
Outlet Pressure Post
.339 Dia. +DFT.
(Set Screw: 3/32” Hex Head)
Accept 5/16” ID Hose Connection
On/Off | Main and |
Switch | Redundant |
| Valves |
|
| Regulator Cover Screw | |
|
| (Reg. Adj. Beneath This Screw) | |
Inlet Pressure Post | On/Off | 3/16” Ground Terminal | |
Control I.D. Label | |||
.339 Dia. +DFT. | Switch | ||
(Set Screw: 3/32” Hex Head) |
|
| |
Accept 5/16” I.D. Hose | 1/4” x .032” THK. Male | ||
Connecon | |||
Spade Terminals (2) | |||
| |||
Fig. 3 – Single Stage Valve Features, Terminals and Wiring
Outlet Pressure Post
Set Screw: 3/32” Hex Head
(.339 Dia. + DFT.)
Accepts 5/16” Hose Connection
| 4.693” Inlet to Outlet |
|
|
| High Fire Regulator |
| |||||
|
|
|
|
| |||||||
|
|
|
|
|
| ||||||
|
|
|
|
| Cover Screw |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| (Reg. Adj. Beneath |
| |||||
|
|
|
|
| the Screw) |
|
|
|
|
|
|
|
|
|
|
| Low Fire Regulator |
| |||||
|
|
|
|
| Cover Screw |
| |||||
|
|
|
|
| (Reg. Adj. Beneath |
| |||||
|
|
|
|
| the Screw) |
| |||||
|
|
| 3/16” x .032” Thick Male |
| |||||||
|
|
| Spade Terminal (1) |
| |||||||
Inlet Pressure Post | On/Off Switch |
|
|
|
|
|
| ||||
Control I.D. Label |
|
|
|
|
|
| |||||
Set Screw: 3/32” Hex Head |
|
|
|
|
|
| |||||
(.339 Dia. + DFT.) |
| 1/4” x .032” Thick Male |
|
|
|
|
|
| |||
Accepts 5/16” Hose Connec†on |
|
|
|
|
|
|
| ||||
| Spade Terminals (3) |
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
| M |
|
|
| ||
|
|
|
|
|
|
|
| ||||
|
|
|
|
| On/Off | Main and | |||||
|
|
|
|
| Switch | Redundant | |||||
|
|
|
|
|
| C |
|
|
|
| Valves (Low Fire) |
|
| 3/16” Ground Terminal | C |
|
|
|
| 2nd Stage | |||
|
|
| |||||||||
|
|
|
|
|
|
| |||||
Valve (High Fire)
Hi
Fig. 4 – Two-Stage Valve Features, Terminals and Wiring
4