Kenwood TS-590S manual Software Enhancing Operating Pleasure, Extended Data-mode Related Functions

Page 44

5 SOFTWARE: ENHANCING OPERATING PLEASURE

In addition to the features we have explained thus far, the TS-590S comes with extensive functions to make your operation more pleasant. We will guide you through some of them.

5.1 Extended Data-mode Related Functions

We have modified data-mode related settings to meet many different needs.

Figure 5-1 Front Panel of the TS-590S

In SSB-DATA and FM-DATA modes, the On/Off settings of the speech processor and the settings of DSP filters are stored independently of the normal SSB and FM modes. Hence, you can conveniently switch between the data mode operation and the normal mode operation with a single touch of a button.

Also, now that USB audio functions*1 accept external audio input/output, operations in combination with a PC have become more convenient. The audio output of the TS-590S can be easily delivered to a PC simply by connecting the transceiver and the PC using a single USB cable. If you select “USB” in “Audio input line selection for data communications” of Menu 63, you can transmit using an audio source from a PC.

The transmit command is given with the PC control command of “TX1;”. During an operation using ARCP-590, in the “Setup TX Control” of the Tool pulldown menu, select “USB” as the modulation line. To transmit via key operation, assign “DATA SEND” to the PF key in menu mode. It is also possible to transmit using the PKS signal in the ACC2 connector as before. Furthermore, by enabling the “Data VOX” function in Menu 69, a transmission can be made automatically using an external signal.

*1 The USB audio interface has latency (signal delay) due to a limitation resulting from the specifications. So a USB device may not be used for a latency-critical application.

38

CONTENTS

TS-590S

Image 44
Contents TS-590S About Copyright Copyright of this Manual and SoftwareAbout Trademarks and Intellectual Properties Other RestrictionsContents Optional Accessory Product Planning Objectives Development Spirit Reception Type of ConversionReception Block diagram Down Conversion Down ConversionMCF Hints and Tips Comparison of Bandpass Characteristics of MCFs Measurement Conditions Up Conversion Dynamic Range in the 50 MHz BandRX Auxiliary Circuits CN101 CN102 CN103 Transmission Kenwood Traditional Transmitting CircuitryIf Circuits FET Final CircuitTransmission Remote Connector High-speed Relay-controlled Antenna TunerMenu N o or N o 1 or DRV Terminal Transmission Output Characteristics of DRV Terminal at 136 kHz and 0 dBm Transmission Comparison C/N Characteristics Local OscillatorDSP Multipurpose 32-bit Floating Point DSPAdvanced AGC Control via if Digital Processing DSPControl Block Diagram of IF-AGC Interference Elimination Within AGC Loop Digital if FilterTypes of Digital if Filters LOW CUTManual Notch Filter and Auto Notch Filter Digital Noise Blanker NB2 Demodulation Modulation Beat Cancel AF Processing DSP-based Auxiliary Circuits for RXNoise Blanker NB2 if Processing Overview of Noise Reduction 11 NB2 Inactive4 NR1 Spectral Subtraction Method AF Processing 13 Conceptual Scheme of NR1 Based on Spectral SubtractionAudio spectrum components swamped by noise 5 NR1 Based on a Line Enhancer AF Processing 16 NR1 Line Enhancer Method Inactive6 NR2 AF Processing 18 NR2 InactiveDSP-based Auxiliary Circuits for TX Speech Processor AF ProcessingDSP-based Auxiliary Circuits Common to TX/RX TX Equalizer & RX Equalizer AF ProcessingSoftware Enhancing Operating Pleasure Extended Data-mode Related FunctionsDrive Out Software Enhancing Operating PleasureSingle Button Toggles if Filters between a and B Operation in the 135 kHz BandDouble Function Keys and Hold Time Selection Mode Selection of Built-in Electronic KeyerPower-on Message PF Keys Quick Memory FunctionCross Tone Function MIC CN Expansion of Voice Guide Function Optional VGS-1 Required Easy Updating of Firmware Projections on the Rear PanelA Sketch of the TS-590S Structural Features CoolingStructural Features Heat Sink Section LCD Amber and GreenMain Control Knob Main Control KnobSystem Configurations Controlling TS-590S from a PC using the COM ConnectorExpansive Application Software Windows Related SoftwareControlling TS-590S from a PC using the USB Connector ConnectionControlling TS-590S from a PC on a Remote Site Software HardwareBasic Specifications Inherited from ARCP-480 User InterfacesKNS Kenwood Network Command System Menu FunctionKNS Welcome Message Visual Scan Audio EqualizerBasic Specifications Inherited from ARHP-10 ARHP-590 Amateur Radio Host Program FreewareNew ARUA-10 USB Audio Controller Freeware Disabling AF Gain Control from ARCP-590Operation SetupBasic Functions Starting and Stopping ARUA-10 Adjusting VolumeAutomatic Execution when Windows Starts New ARVP-10H Amateur Radio VoIP Program Freeware 12 Main Window of ARVP-10HSetup of ARVP-10H Host Station Making ARVP-10H host station Online or OfflineSetup of ARVP-10R remote station Connecting and Disconnecting ARVP-10R Remote StationNew Virtual COM Port Driver 16 Device ManagerOptional Accessory PS-60 Regulated DC Power SupplyRectifier Circuit Comparing Rectification WaveformsPage Revision 1.00 May 15
Related manuals
Manual 92 pages 51.35 Kb