Kenwood TS-590S manual Rectifier Circuit, Comparing Rectification Waveforms

Page 74

9 OPTIONAL ACCESSORY

9.2Rectifier Circuit

Adopts a PFC Circuit that does not Produce Harmonics in an AC Rectifier Circuit

A switching power supply typically produces large harmonics in the rectifier circuit by its switching operation which compromises the phase factor and may cause noise and other disturbances to external devices due to the harmonics that are reflected back to the AC input side.

PS-60 incorporates a PFC-rectifier circuit that produces a rectified waveform close to a sine wave and prevents a compromise of phase factor and disturbances caused by harmonics.

Miniaturized Size by Employing an Interleaved Switching Scheme

By turning On and Off the FET switches on the master and slave sides alternately, the burden on each element is lessened and reliability is improved.

9.3Switching Circuit, Constant-voltage Circuit and Protection Circuit

In the switching circuit, a full-wave current resonance type PFM control circuit is adopted to alternately turn On and Off two FETs in a 50% duty cycle. By defining a certain period of time after both FETs are turned Off, a soft switching operation, in which no current is made to flow at the point of switchover, is made possible to reduce noise.

Figure 9-2 Comparing Rectification Waveforms

A high switching frequency (about 500 kHz) is chosen to enable miniaturization of the transformer for highly-efficient DC conversion.

The DC output voltage after the conversion is monitored by the detection circuit to be compared with the reference voltage in the PFM control circuit in order to control the switching frequency for stabilizing the output voltage. If an overvoltage is detected, the switching of power source stops so as to suspend the DC output.

Also, output current is monitored by the detection circuit and if an overcurrent is detected, the switching frequency is shifted to droop the output voltage and the operation is transited to produce intermittent output.

68

Figure 9-3 Circuit Diagram

CONTENTS

TS-590S

Image 74
Contents TS-590S About Trademarks and Intellectual Properties About CopyrightCopyright of this Manual and Software Other RestrictionsContents Optional Accessory Product Planning Objectives Development Spirit Reception Type of ConversionReception Block diagram Down Conversion Down ConversionMCF Hints and Tips Comparison of Bandpass Characteristics of MCFs Measurement Conditions Up Conversion Dynamic Range in the 50 MHz BandRX Auxiliary Circuits CN101 CN102 CN103 If Circuits TransmissionKenwood Traditional Transmitting Circuitry FET Final CircuitTransmission Remote Connector High-speed Relay-controlled Antenna TunerMenu N o or N o 1 or DRV Terminal Transmission Output Characteristics of DRV Terminal at 136 kHz and 0 dBm Transmission Comparison C/N Characteristics Local OscillatorDSP Multipurpose 32-bit Floating Point DSPAdvanced AGC Control via if Digital Processing DSPControl Block Diagram of IF-AGC Interference Elimination Within AGC Loop Digital if FilterTypes of Digital if Filters LOW CUTManual Notch Filter and Auto Notch Filter Digital Noise Blanker NB2 Demodulation Modulation Beat Cancel AF Processing DSP-based Auxiliary Circuits for RXNoise Blanker NB2 if Processing Overview of Noise Reduction 11 NB2 Inactive4 NR1 Spectral Subtraction Method AF Processing 13 Conceptual Scheme of NR1 Based on Spectral SubtractionAudio spectrum components swamped by noise 5 NR1 Based on a Line Enhancer AF Processing 16 NR1 Line Enhancer Method Inactive6 NR2 AF Processing 18 NR2 InactiveDSP-based Auxiliary Circuits for TX Speech Processor AF ProcessingDSP-based Auxiliary Circuits Common to TX/RX TX Equalizer & RX Equalizer AF ProcessingSoftware Enhancing Operating Pleasure Extended Data-mode Related FunctionsDrive Out Software Enhancing Operating PleasureSingle Button Toggles if Filters between a and B Operation in the 135 kHz BandDouble Function Keys and Hold Time Selection Mode Selection of Built-in Electronic KeyerPower-on Message PF Keys Quick Memory FunctionCross Tone Function MIC CN Expansion of Voice Guide Function Optional VGS-1 Required Easy Updating of Firmware Projections on the Rear PanelA Sketch of the TS-590S Structural Features CoolingStructural Features Heat Sink Section LCD Amber and GreenMain Control Knob Main Control KnobExpansive Application Software System ConfigurationsControlling TS-590S from a PC using the COM Connector Windows Related SoftwareControlling TS-590S from a PC using the USB Connector ConnectionControlling TS-590S from a PC on a Remote Site Software HardwareBasic Specifications Inherited from ARCP-480 User InterfacesKNS Kenwood Network Command System Menu FunctionKNS Welcome Message Visual Scan Audio EqualizerBasic Specifications Inherited from ARHP-10 ARHP-590 Amateur Radio Host Program FreewareNew ARUA-10 USB Audio Controller Freeware Disabling AF Gain Control from ARCP-590Operation SetupBasic Functions Starting and Stopping ARUA-10 Adjusting VolumeAutomatic Execution when Windows Starts New ARVP-10H Amateur Radio VoIP Program Freeware 12 Main Window of ARVP-10HSetup of ARVP-10H Host Station Making ARVP-10H host station Online or OfflineSetup of ARVP-10R remote station Connecting and Disconnecting ARVP-10R Remote StationNew Virtual COM Port Driver 16 Device ManagerOptional Accessory PS-60 Regulated DC Power SupplyRectifier Circuit Comparing Rectification WaveformsPage Revision 1.00 May 15
Related manuals
Manual 92 pages 51.35 Kb