Vertex Standard VX-177 manual CTCSS/DSC/DTMF/EPCS Setting

Page 74

SET (MENU) MODE

REPEATER SETTING

SET MODE ITEM

AVAILABLE VALUES (DEFAULT)

Enables/Disables the Automatic Repeater Shift function.

4 [ARS]

ARS. ON / ARS.OFF

Sets the Repeater Shift Direction.

35

[RPT.MOD]

RPT.OFF / RPT. – / RPT. + (￿)

Sets the magnitude of the repeater Shift.

41

[SHIFT]

0.00 - 99.95 MHz (￿)

CTCSS/DSC/DTMF/EPCS SETTING

SET MODE ITEM

AVAILABLE VALUES (DEFAULT)

Selects the number of CTCSS/DCS Bell ringer repetitions.

7 [BELL]

OFF / 1T / 3T / 5T / 8T / CONT

Setting of the DCS code.

13

[DCS.COD]

104 standard DCS codes (023)

Enables/Disables “Inverted” DCS code decoding.

14

[DCS.N/R]

T/RX N, RX R, TX R, T/RX R

Setting of the DTMF Autodialer Delay Time.

15

[DT DLY]

50MS / 100MS / 250MS / 450MS /

 

 

 

750MS / 1000MS

Setting of the DTMF Autodialer Sending Speed.

16

[DT SPD]

50MS /100MS

Programming of the DTMF Autodialer.

17 [DT WRT]

–

Setting the Receiver Pager Code for the Enhanced CTCSS

18

[ECS.CDR]

(R05_47)

Paging & Code Squelch.

 

 

 

Setting the Transmitting Pager Code for the Enhanced

19

[ECS.CDT]

(T05_47)

CTCSS Paging & Code Squelch.

 

 

 

Enables/Disables split CTCSS/DCS coding.

43

[SPLIT]

SPL.OFF / SPL. ON

Selects the Tone Encoder and/or Decoder mode.

44

[SQL.TYP]

OFF / TONE / TSQL /

 

 

 

REV TN / DCS

Setting of the CTCSS Tone Frequency.

46

[TN FRQ]

50 standard CTCSS tones (100 Hz)

ARTS SETTING

SET MODE ITEM

AVAILABLE VALUES (DEFAULT)

Selects the Beep option during ARTS operation.

2 [AR BEP]

INRANG / ALWAYS / OFF

Selects the Polling Interval during ARTS operation.

3 [AR INT]

25 SEC / 15 SEC

Enables/disables the CW identifier during ARTS operation.

10

[CWID]

TX OFF / TX ON

Programs and activates the CW Identifier (used duringARTS

11 [CW WRT]

–

operation).

 

 

 

MEMORY SETTING

SET MODE ITEM

AVAILABLE VALUES (DEFAULT)

Toggles the display indication between “frequency” and the

28

[NAME]

FREQ / ALPHA

channel’s “Alpha/Numeric Tag.”

 

 

 

Stores Alpha-Numeric “Tags” for the Memory channels.

29

[NM WRT]

–

SCAN SETTING

SET MODE ITEM

AVAILABLE VALUES (DEFAULT)

Selects the Scan Resume mode.

32

[RESUME]

BUSY / HOLD / TIME

Enables/disables the Priority Revert feature.

36

[PRI.RVT]

RVT.OFF / RVT. ON

Selects the Memory Scan channel-selection mode.

39

[SCN MD]

ONLY / MEM

Enables/Disables the Scan lamp while paused.

40

[SCN.LMP]

ON / OFF

Selects the Memory Scan “Skip” channel-selection mode.

42

[SKIP]

OFF / SKIP / ONLY

POWER SAVER SETTING

SET MODE ITEM

AVAILABLE VALUES (DEFAULT)

Selects the Receive-mode Battery Saver interval (“sleep”

37

[RXSAVE]

200 MS / 300 MS / 500 MS /

ratio).

 

 

1 S / 2 S / OFF

Enables/Disables the Transmitter Battery Saver.

49

[TXSAVE]

SAV.OFF / SAV. ON

WIRES™ SETTING

SET MODE ITEM

AVAILABLE VALUES (DEFAULT)

Selects the Internet Link Connection mode.

22

[I NET]

INT.OFF / INT.COD / INT.MEM

Selects the Access Number (DTMF digit) for WIRES™ op-

23

[INT CD]

CODE 0 - CODE 9,

eration.

 

 

CODE A - CODE F, (CODE 1)

Selects the memory register for an Access Number (DTMF

24

[INT MR]

d1 - d9

digit) for non-WIRES™.

 

 

 

72

VX-177 OPERATING MANUAL

Page 73 Page 75
Image 74
Page 73 Page 75
Contents Vertex Standard Yaesu Europe B.VContents General Description Available Options Accessories & OptionsSupplied Accessories Controls & Connectors TOP & Front Panels Controls & Connectors LCD Moni Switch Controls & Connectors Side PanelPTT Push To Talk Switch Controls & Connectors Keypad Functions Press F + KEYOne step or moves the memory Installation of FNB-83 Battery Pack Installation of AccessoriesAntenna Installation Battery Charging LOW Battery IndicationBelt Clip Installation Installation of FBA-25A Alkaline Battery Case OptionInterface of Packet Tncs Operation Switching Power on and OFFAdjusting the Audio Volume Level Frequency Navigation Tuning DialSquelch Adjustment Direct Keypad Frequency Entry ScanningChanging the Transmitter Power Level TransmissionAdvanced Operation Keyboard LockingKEYPAD/LCD Illumination Disabling the Keypad BeeperChecking the Battery Voltage RF SquelchAutomatic Repeater Shift ARS Repeater OperationRepeater Shifts Changing the Default Repeater Shifts Manual Repeater Shift ActivationVFO Split Mode Checking the Repeater Uplink Input FrequencyRepeater Operation CTCSS/DCS/EPCS Operation Ctcss OperationDCS Operation Tone Search Scanning Storing the Ctcss Tone Pairs for Epcs Operation Epcs Enhanced Paging & Code SquelchCTCSS/DCS/EPCS Bell Operation Activating the Enhanced Paging & Code Squelch SystemSplit Tone Operation Tone Calling 1750 HZMemory Storage Memory ModeStoring Independent Transmit Frequencies Odd Splits Memory Recall Home Channel MemoryLabeling Memories Memory Offset Tuning Deleting MemoriesRemoving Memories from a Memory Bank Assigning Memories to a Memory BankMemory Bank Recall Memory Bank OperationMemory only Mode Moving Memory Data to the VFOVX-177 Operating Manual Setting the Scan-Resume Technique ScanningVFO Scanning Manual VFO ScanProgrammed VFO Scan How to Skip Omit a Channel during Memory Scan Operation Memory ScanningPreferential Memory Scan Memory Bank Scan Programmable Band Limit Memory Scan PMS Home Channel Priority VFO PriorityMemory Channel Priority Priority Channel Scanning Dual WatchPriority Revert Mode VFO-VFO Dual WatchAutomatic Lamp Illumination on Scan Stop Band Edge BeeperVX-177 Operating Manual Emergency Feature Emergency Channel OperationEmergency Automatic ID EAI Feature Emergency Feature Storing Smart Search Memories Setting the Smart Search ModeSmart Search Operation Internet Connection Feature Internet Connection Feature Basic Arts Setup and Operation Arts Polling Time Options Arts Alert Beep OptionsCW Identifier Setup Dtmf Autodialer Dtmf OperationManual Dtmf Tone Generation To send the telephone number Dtmf Pager Operation Requires Optional FTD-7 Storing the 3-digit code for the Dtmf Pager OperationActivating the Dtmf Pager Activating the ANI feature Storing the ANI codeMiscellaneous Settings PasswordProgramming the KEY Assignments Changing the Channel StepsReceive Battery Saver Setup TX Battery SaverDisabling the TX/BUSY Indicator Automatic POWER-OFF APO FeatureTransmitter TIME-OUT Timer TOT Busy Channel LOCK-OUT BcloDCS Code Inversion Changing the TX Deviation Level Reset Procedures Cloning Try againVX-177 Operating Manual SET Menu Mode ARSNET CTCSS/DSC/DTMF/EPCS Setting ANI Set Mode Item 3 AR INT Set Mode Item 1 APOSet Mode Item 2 AR BEP Set Mode Item 4 ARSSet Mode Item 10 Cwid Set Mode Item 8 BSY.LEDSet Mode Item 9 CLK.SFT Set Mode Item 11 CW WRTSet Mode Item 19 ECS.CDT Set Mode Item 17 DT WRTSet Mode Item 18 ECS.CDR Set Mode Item 20 EDG.BEPSet Mode Item 24 INT MR Set Mode Item 22 I NETSet Mode Item 23 INT CD Set Mode Item 25 LampSet Mode Item 29 NM WRT Set Mode Item 27 M/T-CLSet Mode Item 28 Name Set Mode Item 30 PswdSet Mode Item 35 RPT.MOD Set Mode Item 33 REV/HMSet Mode Item 34 RF SQL Set Mode Item 36 PRI.RVTSet Mode Item 41 Shift Set Mode Item 39 SCN MDSet Mode Item 40 SCN.LMP Set Mode Item 42 SkipSet Mode Item 46 TN FRQ Set Mode Item 44 SQL.TYPSet Mode Item 45 Step Set Mode Item 47 TOTSet Mode Item 53 ANI Set Mode Item 51 WID.NARSet Mode Item 52 EAI Set Mode Item 54 ANI.WRTSpecifications GeneralInstallation of the FTD-7 Dtmf Paging Unit Option Declaration by Manufacturer 0511X-0K
Top Page Image Contents