Genius IC-M21 instruction manual SET Mode, SET mode programming, SET mode items, Beep tone bP

Page 18

6 SET MODE

■SET mode programming

SET mode is used to change the conditions of 11 transceiver functions: beep tone, scan type, scan resure timer, auto scan, monitor action, automatic backlighting, LCD contrast, auto power save, self check, battery voltage and S/RF meter.

qTurn power OFF.

wWhile pushing [SQL•MONI], turn power ON and continue pushing [SQL•MONI] until “bP” appears.

eRelease [SQL•MONI].

rPush [Y]/[Z] to select the desired condition of the item. t Push [SQL•MONI] to select the desired item, if necessary. y To exit SET mode, turn the power OFF, then ON again, or

push [16•C].

SET MODE CONSTRUCTION

	Battery	S/RF	Beep tone		Scan	Scan resume
	voltage	meter	Beep tone		type	timer
	voltage	meter			type	timer
			Starting item
	Self					Auto
	check			MONI		scan
				MONI
			Push	SQL
	Auto		LCD		Automatic	Monitor
	power save	contrast		backlighting		action

■SET mode items

DBeep tone “bP”

You can select silent operation by turning beep tones OFF or you can have confirmation beeps sound at the push of a switch by turning beep tones ON.

•AUTO (At): Beep tone is linked with volume tone.

•1–10: Beep tone scale is set from 1–10 scale (Max. is 10).

Beep tone AUTO (default)

DPriority scan function “Pr”

The transceiver has 2 scan types. Normal scan and priority scan. Normal scan searches all tag channels in the selected channel group. Priority scan searches all tag channels in se- quence while monitoring Channel 16.

Priority scan (default)

13

Image 18

Contents IM21 Clean the Transceiver Thoroughly with Fresh Case of EmergencyEquipment damage may occur Word Definition RwarningMay occur If disregarded, inconvenience only. No riskPage Table of Contents Privacy Operating RulesPriorities Radio licenses0PTT Switch PTT Panel DescriptionFront, top and side panels Battery Case Release Screw To remove the battery case If the seal is damaged, water resistant is not guaranteedScan Indicator p Transmit Indicator pBusy Indicator p Duplex Indicator0BATTERY Indicator 5TRANSMIT Power Indicator3CHANNEL Number Readout Channel Basic OperationChannel selection Call channelLock function Adjusting the squelch levelPush SQLMONI, then adjust the squelch level with Y/Z Appears while the lock function is usedSet squelch level Set output power Rotate OFF/VOL clockwise to turn power onPower on Set volume Push to Transmit Release to receive Receiving and transmittingCall channel programming Automatic backlightingPush any key except for PTT to turn the backlighting on Operation DUALWATCH/TRI-WATCHDescription DUALWATCH/TRI-WATCH SimulationPriority Scan Scan OperationScan types Normal ScanStarting a scan Setting tag channelsTo cancel the tag channel setting, push Scntag for 1 sec To stop the scan, push ScntagSET mode items SET ModeSET mode programming Beep tone bPAuto scan function AS Scan resume timer StScan indicator blinks while scanning Monitor action selection SqLCD contrast selection LC Auto power save function PSContrast of the LCD can be adjusted from 4 levels Self check function SCBattery voltage indicator bt Meter/RF meter indicator SrFunction Indication Switch Battery Charging Battery chargingBattery cautions Installing batteries Battery case Charging connectionsOptional battery chargers Rapid charging with the BC-119N+AD-103Rapid charging with the BC-121N+AD-103 Flexible antenna Supplied Accessories and AttachmentsSupplied accessories HandstrapSwivel belt clip To attachTo remove Troubleshooting Problem Possible Cause SolutionCeiver works properly or not Low power only Channel ListInternational channels Specifications and Options SpeciﬁcationsOptions 0560 Count on us Kamiminami, Hirano-ku, Osaka 547-0002 Japan