Icom IC-R5 instruction manual Full/band/programmed scan, Select VFO mode with V/MS.MW~

Page 37

■Full/band/programmed scan

qSelect VFO mode with [V/M•S.MW•~].

•Select the desired frequency band with [BAND•], if desired. wSet the squelch to the point where noise is just muted. ePush [MODE•SCAN] for 1 sec. to enter scanning type se-

lection condition.

rRotate [DIAL] to select the desired scanning type.

•“ALL” for full scan; “BAND” for band scan, “PROGxx” for pro- grammed scan (xx= 0 to 24; programmed scan edges numbers only displayed)

• Full scan selection

[DIAL]

• Band scan selection

[MODE•SCAN]

• Programmed scan selection

Selectable between “ 0” to “24” if programmed

SCAN OPERATION 6

tTo start the scan, push [MODE•SCAN].

•Scan pauses when a signal is received.

•Rotate [DIAL] to change the scanning direction, or resumes manually.

•Push [MODE•SCAN] again to stop the scan.

• During full/band scan		• During programmed scan		6
FM	P SKIP	FM	P SKIP

NOTE: Instead of the steps e to t operations, while

pushing and holding [MODE•SCAN], rotate [DIAL] to se-

lect the desired scan type. In this case, scan starts when releasing [MODE•SCAN].

About the scanning steps: The selected tuning step in each frequency band (in VFO mode) is used during scan.

26

Image 37

Contents IR5 Explicit Definitions Precaution Iii Supplied AccessoriesTable of Contents Quick Reference Guide Battery installationPreparation Belt clipRotate Dial to select Y then push Band Install the Ni-Cd batteriesCharging conﬁrmation is displayed as below Your ﬁrst scanning Experience About default settingBasic operation Setting frequency Receive mode selectionMemory programming Selecting a memory ChannelProgramming scan edges Programmed scan operationSelecting a scan edge channel a Selecting a scan edge channel BCancelling scan Starting scan Select VFO modeSelecting a scanning type Starting scanFront, top and side panels Panel DescriptionUCONTROL Dial Dial Push for 1 sec. to turn the receiver power on and OFFERECEIVE Mode Indicator p WLOCK Indicator pRDUPLEX Indicators p TTONE Indicators1SIGNAL Strength Indicator p Priority Watch Indicator p2VOLUME Exchange Indicator p Battery installation Battery ChargingBattery caution Charging cautionCharging connections Battery chargingCharging description Charging periods Approx hoursVFO and memory channels Frequency and Channel SettingOperating band selection Available frequency bands Frequency and Channel SettingSetting a tuning step Setting a frequencyTuning step selection Rotate Dial to select the desired frequency bandSelecting a memory channel Push V/MS.MW~ to select the memory modeLock function Rotate Dial to select the desired memory channelWhen a signal is received Setting audio volumeBasic Operation ReceivingReceive mode selection Squelch level settingAttenuator function Monitor functionPush and hold SQL to monitor the operating frequency Duplex operation SettingRotate Dial to select DUP Push Tsset momentarily to exit set mode Setting dial select stepDial select step General description Memory ChannelsRotate Dial to select the desired bank channel number Memory bank settingPush V/MS.MW~ momentarily to set the channel into the bank Push V/MS.MW~ to select memory mode, if desired Memory bank selectionRotate Dial to select the bank channel To return to regular memory condition, rotate Dial whileRotate Dial to move the cursor to left or right Programming memory/bank nameAvailable characters Selecting bank channel indication Selecting display typeCopying memory contents Memory clearing Push V/MS.MW~ for 1 sec. to clear the contentsWhile pushing FUNC, push V/MS.MW~ for 1 sec EssaryTransferring memory contents Erasing/transferring bank contents Scan types Scan OperationFull Scan p FREQUENCY/MEMORY Skip Function pFull/band/programmed scan Select VFO mode with V/MS.MW~To start the scan, push Modescan Example Programming 145.300 MHz into scan edges 03A Scan edges programmingMemory/bank/all bank scan Select memory mode with V/MS.MW~During auto-memory write scanning Auto memory write scanRe-calling the stored frequencies Clearing the stored frequenciesNel Skip channel/frequency settingScan resume timer Scan pause timerScan resume condition Priority watch types Priority WatchAbout priority beep function Watch startsPush Tsset to cancel the watch Push Tsset to exit set mode and start the watchPriority watch operation Select memory mode, or the desired bank group thenWhen scanning memory/bank channels VFO scan watch qSelect memory mode0Push Tsset to cancel the watch and scan Tone/DTCS squelch operation Tone Squelch and Pocket BeepOPush Func to stop the beeps and blinking manually Step yAvailable Dtcs code list Tone squelch frequency/DTCS code settingAvailable tone frequency list Dtcs polarity setting While pushing FUNC, push Modescan to start the tone scan Tone scanSet mode entering and operation SET ModeExpanded set mode ON/OFF GeneralGeneral set mode items Set mode itemsExpanded set mode items Priority watch Dial select stepKey-touch beep Beep output levelAntenna selection Power saveMHz differ according to version, re No accessible switch is available, except Monitor switch actionKey lock effect Dial speed accelerationScan pause timer Auto power OFFScan resume timer Scan stop beepDuplex direction Offset frequencyTone squelch Dtcs polarity DTone frequency Ddtcs codeAvailable subaudible tone frequencies Available Dtcs codeWeather alert function LCD contrastTurns weather alert function on and OFF Antenna selection Other FunctionsSelecting antenna Weather channel operation Dial function assignmentWeather channel selection Turn the weather alert function OFF in set mode Push SQL on the master receiver Cloning between receiversCloning using a personal computer Auto power-off functionCloning error Partial reset TV channels Frequency TableDU.S.A. channels Dccir channelsDNew DChina channelsZealand ChannelsDItalian channels Indonesian channelsTaiwan channels FOT channelsWeather channelsunit MHz VHF marine channelsMurs channels Other communications in the USAHF CB Citizens Band channels General aviation frequencies Wireless MicrophonesDCable TV IRC Other communications- other countries LPD Low Power Device channels Unit MHzPMR446 channels unit MHz UHF C.R.S Citizen Radio Service channels Troubleshooting MaintenanceCP-18A/E fuse replacement Dgeneral SpecificationsOptions OptionsPocket Guide Memory channel programming We Icom Inc. Japan Declaration ConformityKamiminami, Hirano-ku, Osaka 547-0003 Japan