Icom IC-R5 instruction manual UHF C.R.S Citizen Radio Service channels

Page 72

11 FREQUENCY TABLE

DUHF C.R.S (Citizen Radio Service) channels

Frequency

1476.425 MHz

2476.450 MHz

3476.475 MHz

4476.500 MHz

5476.525 MHz

6476.550 MHz

7476.575 MHz

8476.600 MHz

9476.625 MHz

10 476.650 MHz

11 476.675 MHz

12 476.700 MHz

13 476.725 MHz

14 476.750 MHz

15 476.775 MHz

16 476.800 MHz

17 476.825 MHz

18 476.850 MHz

19 476.875 MHz

20 476.900 MHz

Frequency

21476.925 MHz

22476.950 MHz

23476.975 MHz

24477.000 MHz

25477.025 MHz

26477.050 MHz

27477.075 MHz

28477.100 MHz

29477.125 MHz

30477.150 MHz

31477.175 MHz

32477.200 MHz

33477.225 MHz

34477.250 MHz

35477.275 MHz

36477.300 MHz

37477.325 MHz

38477.350 MHz

39477.375 MHz

40477.400 MHz

Image 72

Contents IR5 Explicit Definitions Precaution Supplied Accessories IiiTable of Contents Battery installation Quick Reference GuidePreparation Belt clipInstall the Ni-Cd batteries Rotate Dial to select Y then push BandCharging conﬁrmation is displayed as below About default setting Your ﬁrst scanning ExperienceBasic operation Receive mode selection Setting frequencyMemory programming Selecting a memory ChannelProgrammed scan operation Programming scan edgesSelecting a scan edge channel a Selecting a scan edge channel BStarting scan Select VFO mode Cancelling scanSelecting a scanning type Starting scanPanel Description Front, top and side panelsPush for 1 sec. to turn the receiver power on and OFF UCONTROL Dial DialWLOCK Indicator p ERECEIVE Mode Indicator pRDUPLEX Indicators p TTONE IndicatorsPriority Watch Indicator p 1SIGNAL Strength Indicator p2VOLUME Exchange Indicator p Battery Charging Battery installationBattery caution Charging cautionBattery charging Charging connectionsCharging description Charging periods Approx hoursFrequency and Channel Setting VFO and memory channelsOperating band selection Frequency and Channel Setting Available frequency bandsSetting a frequency Setting a tuning stepTuning step selection Rotate Dial to select the desired frequency bandPush V/MS.MW~ to select the memory mode Selecting a memory channelLock function Rotate Dial to select the desired memory channelSetting audio volume When a signal is receivedBasic Operation ReceivingSquelch level setting Receive mode selectionMonitor function Attenuator functionPush and hold SQL to monitor the operating frequency Setting Duplex operationRotate Dial to select DUP Setting dial select step Push Tsset momentarily to exit set modeDial select step Memory Channels General descriptionMemory bank setting Rotate Dial to select the desired bank channel numberPush V/MS.MW~ momentarily to set the channel into the bank Memory bank selection Push V/MS.MW~ to select memory mode, if desiredRotate Dial to select the bank channel To return to regular memory condition, rotate Dial whileProgramming memory/bank name Rotate Dial to move the cursor to left or rightAvailable characters Selecting display type Selecting bank channel indicationCopying memory contents Push V/MS.MW~ for 1 sec. to clear the contents Memory clearingWhile pushing FUNC, push V/MS.MW~ for 1 sec EssaryTransferring memory contents Erasing/transferring bank contents Scan Operation Scan typesFull Scan p FREQUENCY/MEMORY Skip Function pSelect VFO mode with V/MS.MW~ Full/band/programmed scanTo start the scan, push Modescan Scan edges programming Example Programming 145.300 MHz into scan edges 03ASelect memory mode with V/MS.MW~ Memory/bank/all bank scanAuto memory write scan During auto-memory write scanningRe-calling the stored frequencies Clearing the stored frequenciesSkip channel/frequency setting NelScan pause timer Scan resume timerScan resume condition Priority Watch Priority watch typesAbout priority beep function Watch startsPush Tsset to exit set mode and start the watch Push Tsset to cancel the watchPriority watch operation Select memory mode, or the desired bank group thenVFO scan watch qSelect memory mode When scanning memory/bank channels0Push Tsset to cancel the watch and scan Tone Squelch and Pocket Beep Tone/DTCS squelch operationOPush Func to stop the beeps and blinking manually Step yTone squelch frequency/DTCS code setting Available Dtcs code listAvailable tone frequency list Dtcs polarity setting Tone scan While pushing FUNC, push Modescan to start the tone scanSET Mode Set mode entering and operationExpanded set mode ON/OFF GeneralSet mode items General set mode itemsExpanded set mode items Dial select step Priority watchKey-touch beep Beep output levelPower save Antenna selectionMHz differ according to version, re Monitor switch action No accessible switch is available, exceptKey lock effect Dial speed accelerationAuto power OFF Scan pause timerScan resume timer Scan stop beepOffset frequency Duplex directionTone squelch DTone frequency Ddtcs code Dtcs polarityAvailable subaudible tone frequencies Available Dtcs codeLCD contrast Weather alert functionTurns weather alert function on and OFF Other Functions Antenna selectionSelecting antenna Dial function assignment Weather channel operationWeather channel selection Turn the weather alert function OFF in set mode Cloning between receivers Push SQL on the master receiverAuto power-off function Cloning using a personal computerCloning error Partial reset Frequency Table TV channelsDU.S.A. channels Dccir channelsDChina channels DNewZealand ChannelsIndonesian channels DItalian channelsTaiwan channels FOT channelsVHF marine channels Weather channelsunit MHzOther communications in the USA Murs channelsHF CB Citizens Band channels Wireless Microphones General aviation frequenciesDCable TV IRC LPD Low Power Device channels Unit MHz Other communications- other countriesPMR446 channels unit MHz UHF C.R.S Citizen Radio Service channels Maintenance TroubleshootingCP-18A/E fuse replacement Specifications DgeneralOptions OptionsPocket Guide Memory channel programming Declaration Conformity We Icom Inc. JapanKamiminami, Hirano-ku, Osaka 547-0003 Japan