Icom IC-R5 instruction manual Other Functions, Antenna selection, Selecting antenna

Page 59

■Antenna selection

USING EXPANDED SET MODE

The IC-R5 has an internal bar antenna for receiving AM broadcast band (0.495–1.620 MHz) signals. In addition, the connected earphone’s cable can be used as an antenna for receiving FM broadcast band (76.000–107.995 MHz; differ ac- cording to version) signals.

DSelecting antenna

qSelect VFO mode with [V/M•S.MW•~].


wPush [BAND•		] several times, or while pushing
[BAND•	] rotate [DIAL] to select the AM or FM broad-

OTHER FUNCTIONS 10

tWhile pushing [FUNC], rotate [DIAL] to select “BAR” when set mode has accessed from the AM broadcast band; se- lect “EAR” when set mode has accessed from the FM broadcast band.

Bar antenna selection	Earphone cable selection
for 0.495–1.620 MHz band	for 76.000–107.995 MHz band	9
		9

cast band.

ePush [TS•SET] for 1 sec. to enter set mode.

rRotate [DIAL] to select “ANT” item.

yPush [TS•SET] momentarily to exit set mode.

NOTE:

10

• “ANT” disappears after 1 sec. and “EXT” (default) and “An” ap-

pear.

[DIAL]

[FUNC]

After 1 sec.

[TS•SET]

• Some noise or spurious may be received when the inter-

nal bar or earphone cable is used for antenna.

• The supplied or third party’s antenna MUST BE con-

nected to the antenna connector to receive signals other

than AM or FM broadcast bands.

• When receiving an AM broadcast signal with internal bar

antenna, aim the receiver to better audio direction.

• When the internal bar or earphone cable is used for an- tenna, the attenuator function cannot be used.

48

Image 59

Contents IR5 Explicit Definitions Precaution Iii Supplied AccessoriesTable of Contents Belt clip Battery installationQuick Reference Guide PreparationCharging conﬁrmation is displayed as below Install the Ni-Cd batteriesRotate Dial to select Y then push Band Basic operation About default settingYour ﬁrst scanning Experience Selecting a memory Channel Receive mode selectionSetting frequency Memory programmingSelecting a scan edge channel B Programmed scan operationProgramming scan edges Selecting a scan edge channel aStarting scan Starting scan Select VFO modeCancelling scan Selecting a scanning typeFront, top and side panels Panel DescriptionUCONTROL Dial Dial Push for 1 sec. to turn the receiver power on and OFFTTONE Indicators WLOCK Indicator pERECEIVE Mode Indicator p RDUPLEX Indicators p2VOLUME Exchange Indicator p Priority Watch Indicator p1SIGNAL Strength Indicator p Charging caution Battery ChargingBattery installation Battery cautionCharging periods Approx hours Battery chargingCharging connections Charging descriptionOperating band selection Frequency and Channel SettingVFO and memory channels Available frequency bands Frequency and Channel SettingRotate Dial to select the desired frequency band Setting a frequencySetting a tuning step Tuning step selectionRotate Dial to select the desired memory channel Push V/MS.MW~ to select the memory modeSelecting a memory channel Lock functionReceiving Setting audio volumeWhen a signal is received Basic OperationReceive mode selection Squelch level settingPush and hold SQL to monitor the operating frequency Monitor functionAttenuator function Rotate Dial to select DUP SettingDuplex operation Dial select step Setting dial select stepPush Tsset momentarily to exit set mode General description Memory ChannelsPush V/MS.MW~ momentarily to set the channel into the bank Memory bank settingRotate Dial to select the desired bank channel number To return to regular memory condition, rotate Dial while Memory bank selectionPush V/MS.MW~ to select memory mode, if desired Rotate Dial to select the bank channelAvailable characters Programming memory/bank nameRotate Dial to move the cursor to left or right Selecting bank channel indication Selecting display typeCopying memory contents Essary Push V/MS.MW~ for 1 sec. to clear the contentsMemory clearing While pushing FUNC, push V/MS.MW~ for 1 secTransferring memory contents Erasing/transferring bank contents FREQUENCY/MEMORY Skip Function p Scan OperationScan types Full Scan pTo start the scan, push Modescan Select VFO mode with V/MS.MW~Full/band/programmed scan Example Programming 145.300 MHz into scan edges 03A Scan edges programmingMemory/bank/all bank scan Select memory mode with V/MS.MW~Clearing the stored frequencies Auto memory write scanDuring auto-memory write scanning Re-calling the stored frequenciesNel Skip channel/frequency settingScan resume condition Scan pause timerScan resume timer Watch starts Priority WatchPriority watch types About priority beep functionSelect memory mode, or the desired bank group then Push Tsset to exit set mode and start the watchPush Tsset to cancel the watch Priority watch operation0Push Tsset to cancel the watch and scan VFO scan watch qSelect memory modeWhen scanning memory/bank channels Step y Tone Squelch and Pocket BeepTone/DTCS squelch operation OPush Func to stop the beeps and blinking manuallyAvailable tone frequency list Tone squelch frequency/DTCS code settingAvailable Dtcs code list Dtcs polarity setting While pushing FUNC, push Modescan to start the tone scan Tone scanGeneral SET ModeSet mode entering and operation Expanded set mode ON/OFFExpanded set mode items Set mode itemsGeneral set mode items Beep output level Dial select stepPriority watch Key-touch beepMHz differ according to version, re Power saveAntenna selection Dial speed acceleration Monitor switch actionNo accessible switch is available, except Key lock effectScan stop beep Auto power OFFScan pause timer Scan resume timerTone squelch Offset frequencyDuplex direction Available Dtcs code DTone frequency Ddtcs codeDtcs polarity Available subaudible tone frequenciesTurns weather alert function on and OFF LCD contrastWeather alert function Selecting antenna Other FunctionsAntenna selection Weather channel selection Dial function assignmentWeather channel operation Turn the weather alert function OFF in set mode Push SQL on the master receiver Cloning between receiversCloning error Auto power-off functionCloning using a personal computer Partial reset Dccir channels Frequency TableTV channels DU.S.A. channelsChannels DChina channelsDNew ZealandFOT channels Indonesian channelsDItalian channels Taiwan channelsWeather channelsunit MHz VHF marine channelsHF CB Citizens Band channels Other communications in the USAMurs channels DCable TV IRC Wireless MicrophonesGeneral aviation frequencies PMR446 channels unit MHz LPD Low Power Device channels Unit MHzOther communications- other countries UHF C.R.S Citizen Radio Service channels Troubleshooting MaintenanceCP-18A/E fuse replacement Dgeneral SpecificationsOptions OptionsPocket Guide Memory channel programming We Icom Inc. Japan Declaration ConformityKamiminami, Hirano-ku, Osaka 547-0003 Japan