Icom IC-R5 instruction manual Other communications- other countries, PMR446 channels unit MHz

Page 71

FREQUENCY TABLE 11

■Other communications— other countries

DLPD (Low Power Device) channels

(unit: MHz)

DPMR446 channels (unit: MHz)

Frequency

1433.075

2433.100

3433.125

4433.150

5433.175

6433.200

7433.225

8433.250

9433.275

10433.300

11433.325

12433.350

13433.375

14433.400

15433.425

16433.450

17433.475

18433.500

19433.525

20433.550

21433.575

22433.600

23433.625

24433.650

25433.675

26433.700

27433.725

28433.750

29433.775

Frequency

30433.800

31433.825

32433.850

33433.875

34433.900

35433.925

36433.950

37433.975

38434.000

39434.025

40434.050

41434.075

42434.100

43434.125

44434.150

45434.175

46434.200

47434.225

48434.250

49434.275

50434.300

51434.325

52434.350

53434.375

54434.400

55434.425

56434.450

57434.475

58434.500

Frequency

59434.525

60434.550

61434.575

62434.600

63434.625

64434.650

65434.675

66434.700

67434.725

68434.750

69434.775

Frequency

1446.00625

2446.01875

3446.03125

4446.04375

5446.05625

6446.06875

7446.08125

8446.09375

Image 71

Contents IR5 Explicit Definitions Precaution Iii Supplied AccessoriesTable of Contents Belt clip Battery installationQuick Reference Guide PreparationCharging conﬁrmation is displayed as below Install the Ni-Cd batteriesRotate Dial to select Y then push Band Basic operation About default settingYour ﬁrst scanning Experience Selecting a memory Channel Receive mode selectionSetting frequency Memory programmingSelecting a scan edge channel B Programmed scan operationProgramming scan edges Selecting a scan edge channel aStarting scan Starting scan Select VFO modeCancelling scan Selecting a scanning typeFront, top and side panels Panel DescriptionUCONTROL Dial Dial Push for 1 sec. to turn the receiver power on and OFFTTONE Indicators WLOCK Indicator pERECEIVE Mode Indicator p RDUPLEX Indicators p2VOLUME Exchange Indicator p Priority Watch Indicator p1SIGNAL Strength Indicator p Charging caution Battery ChargingBattery installation Battery cautionCharging periods Approx hours Battery chargingCharging connections Charging descriptionOperating band selection Frequency and Channel SettingVFO and memory channels Available frequency bands Frequency and Channel SettingRotate Dial to select the desired frequency band Setting a frequencySetting a tuning step Tuning step selectionRotate Dial to select the desired memory channel Push V/MS.MW~ to select the memory modeSelecting a memory channel Lock functionReceiving Setting audio volumeWhen a signal is received Basic OperationReceive mode selection Squelch level settingPush and hold SQL to monitor the operating frequency Monitor functionAttenuator function Rotate Dial to select DUP SettingDuplex operation Dial select step Setting dial select stepPush Tsset momentarily to exit set mode General description Memory ChannelsPush V/MS.MW~ momentarily to set the channel into the bank Memory bank settingRotate Dial to select the desired bank channel number To return to regular memory condition, rotate Dial while Memory bank selectionPush V/MS.MW~ to select memory mode, if desired Rotate Dial to select the bank channelAvailable characters Programming memory/bank nameRotate Dial to move the cursor to left or right Selecting bank channel indication Selecting display typeCopying memory contents Essary Push V/MS.MW~ for 1 sec. to clear the contentsMemory clearing While pushing FUNC, push V/MS.MW~ for 1 secTransferring memory contents Erasing/transferring bank contents FREQUENCY/MEMORY Skip Function p Scan OperationScan types Full Scan pTo start the scan, push Modescan Select VFO mode with V/MS.MW~Full/band/programmed scan Example Programming 145.300 MHz into scan edges 03A Scan edges programmingMemory/bank/all bank scan Select memory mode with V/MS.MW~Clearing the stored frequencies Auto memory write scanDuring auto-memory write scanning Re-calling the stored frequenciesNel Skip channel/frequency settingScan resume condition Scan pause timerScan resume timer Watch starts Priority WatchPriority watch types About priority beep functionSelect memory mode, or the desired bank group then Push Tsset to exit set mode and start the watchPush Tsset to cancel the watch Priority watch operation0Push Tsset to cancel the watch and scan VFO scan watch qSelect memory modeWhen scanning memory/bank channels Step y Tone Squelch and Pocket BeepTone/DTCS squelch operation OPush Func to stop the beeps and blinking manuallyAvailable tone frequency list Tone squelch frequency/DTCS code settingAvailable Dtcs code list Dtcs polarity setting While pushing FUNC, push Modescan to start the tone scan Tone scanGeneral SET ModeSet mode entering and operation Expanded set mode ON/OFFExpanded set mode items Set mode itemsGeneral set mode items Beep output level Dial select stepPriority watch Key-touch beepMHz differ according to version, re Power saveAntenna selection Dial speed acceleration Monitor switch actionNo accessible switch is available, except Key lock effectScan stop beep Auto power OFFScan pause timer Scan resume timerTone squelch Offset frequencyDuplex direction Available Dtcs code DTone frequency Ddtcs codeDtcs polarity Available subaudible tone frequenciesTurns weather alert function on and OFF LCD contrastWeather alert function Selecting antenna Other FunctionsAntenna selection Weather channel selection Dial function assignmentWeather channel operation Turn the weather alert function OFF in set mode Push SQL on the master receiver Cloning between receiversCloning error Auto power-off functionCloning using a personal computer Partial reset Dccir channels Frequency TableTV channels DU.S.A. channelsChannels DChina channelsDNew ZealandFOT channels Indonesian channelsDItalian channels Taiwan channels Weather channelsunit MHz VHF marine channelsHF CB Citizens Band channels Other communications in the USAMurs channels DCable TV IRC Wireless MicrophonesGeneral aviation frequencies PMR446 channels unit MHz LPD Low Power Device channels Unit MHzOther communications- other countries UHF C.R.S Citizen Radio Service channels Troubleshooting MaintenanceCP-18A/E fuse replacement Dgeneral SpecificationsOptions OptionsPocket Guide Memory channel programming We Icom Inc. Japan Declaration ConformityKamiminami, Hirano-ku, Osaka 547-0003 Japan