Marantz VP-12S3/VP-12S3L manual Error Mode, On Screen Message

Page 45

ERROR MODE

WARNING/LAMP indicator, POWER ON indicator, and STANDBY indicator diagnose error mode of the projector as follows.

	Error mode		Indicators		Possible Cause	Recommendation
		WARNING	POWER ON	STANDBY
		/LAMP

	Lamp cover	ON	OFF	Flashing	The lamp cover is not	Close the cover correctly.
					closed properly.

	Lamp	ON	OFF	OFF	The lamp has failed, or	Replace the lamp and
					the lamp is completely	reset lamp life.
					worn out.

	Temperature	Flashing	OFF	Flashing	Projector internal
					temperature is higher
					than the allowed level.	Check if anything is
	Fan	Flashing	OFF	ON	Trouble has occurred	blocking the exhaust vent.
					with the fan.

	Color temperature	ON	OFF	ON	Color temperature	Retry adjustment.
	adjustment				adjustment failed.

	Other	Flashing	OFF	OFF	Internal program error	Shut power OFF and
						ON again.

ENGLISH

ON SCREEN MESSAGE

Use the list below to check the message displayed on the screen.

Message	Meaning	Remedy
NO SIGNAL	No input signal.	Properly connect the cables.
REPLACE LAMP!	The lamp has reached the end of its life.	Replace the lamp and reset lamp life.

OUT OF RANGE	Improper signal feed to the projector.	Adjust resolution, V(Hz) : refresh rate of the
OUT OF RANGE		equipment, referring to the Timing Chart.
		equipment, referring to the Timing Chart.

39

Image 45

Contents Model VP-12S3/VP-12S3L User Guide For the customers in the USA Important Safety Instructions Lamp Handing Precautions Precauciones para la manipulación de la lámpara Table of Contents Replacement Important SafeguardsFeatures Easy to install and operateDesigned for silence and safety Lens Cap x Remote Controller x AccessoriesProjection Lens IR sensor Front and Top ViewTerminals Rear and Terminals ViewTerminals Bottom ViewInput Remote ControllerPreparing the Remote Controller Remote Controller Operational RangeWhen pulling out a cable When making connections be sure toConnection with AC Power Supply ConnectionAdvanced Connection Connection with a HD-Video, Satellite, Cable Tuner or PCTurning on the Power Initial SettingZooming and Focusing Adjusting the Image PositionDetail Focusing Adjusting the HeightReturning the Projector to its Initial Position Counterclockwise DownKeystone Correction Recommended Setting InstallationInstalling on a tabletop Mounting on the ceilingScreen Size and Projection Distance inch VP-12S3 16 9 ScreenScreen Diagonal Width Height Minimum Maximum Inch Screen Size and Projection Distance m VP-12S319 5/8 78 9/16 107 1/16 Screen Size and Projection Distance inch VP-12S3LMinimum Maximum Screen Size and Projection Distance mm VP-12S3LSelecting the Input Signal Source Selecting the Aspect ModeBasic Operations Screen Images in a 169 screen Screen Images in a 43 screen To Turn off the Power Menu Structure OperationsHow to Operate Menus Picture Mode and MemoryPicture mode Index Color Temp. Temperature Picture AdjustSetting the Picture Adjust Menu ContrastFine Menu DelayLuminance ChrominanceMiscellaneous Sub ControlSetting Setting the Setting Menu2-2 pull down for PAL System Setting the System MenuDisplay Setting the Display MenuAuto Power Off ConfigurationReset Lamp Life OSD Position 169Setting the Trigger 2 Menu Setting the Config MenuTrigger On Output DC Off No outputSetting the Preset Menu PresetMemorizing settings in an index Gamma settingLamp Life and Replace Lamp MaintenanceLamp Life To clear the warning, p ss the Menu buttonHow to replace the Lamp Unit Initialize the Lamp LifeReplacing Lamp Unit English Color Temperature Adjustment When installed on a tabletopWhen installed on a ceiling Cleaning the Lens Color Temperature Sensor ProtectionReplacement Parts Optional AccessoriesTroubleshooting On Screen Message Error ModeOptical characteristics SpecificationsAccessories Input/OutputKHz Scan Timing chartFront DimensionsBottom RearGlossary Black Level Black setupAspect ratio KeystoneIs a registered trademark