Marantz VP-12S3/VP-12S3L manual Important Safeguards, Replacement

Page 7

IMPORTANT SAFEGUARDS

Caution Concerning the Lamp

Replacement

There is potential glass particle hazard if the lamp ruptures.

Caution Concerning the Lamp Unit

There is a potential hazard of glass particle if the lamp ruptures.

In case of lamp rupture,contact your nearest Marantz Authorized Dealer or Service Center for a replacement. See “Replacing Lamp Unit”. (☞ P.34)

WARNING

 

 

THIS COVER IS PROVIDED WITH

 

 

INTERLOCK TO REDUCE THE RISK OF

 

 

EXCESSIVE ULTRAVIOLET RADIATION.

 

 

DO NOT DEFEAT ITS PORPOSE OR

CAUTION :

CAUTION HOT :

ATTEMPT TO SERVICE WITHOUT

 

MODEL NO. VP-16S1 / U1M

REMOVING COVER COMPLETELY.

 

AC 120V 60H 2.0A

 

ATTENTION :

ATTENTION CHAUD :

ENGLISH

WARNING

THIS COVER IS PROVIDED WITH INTERLOCK TO REDUCE THE RISK OF EXCESSIVE ULTRAVIOLET RADIATION. DO NOT DEFEAT ITS PORPOSE OR ATTEMPT TO SERVICE WITHOUT REMOVING COVER COMPLETELY.

CAUTION : HIGH PRESSURE LAMP

CAUTION HOT : UNPLUG

M

MAY EXPLODED IF IMPROPERLY HANDLED.

THE POWER CORD AND WAIT

REFER SERVICING TO QUALIFIED SERVICE

60 MINUTES BEFORE CHARGING

 

PERSONNEL.

THE LAMP.

 

ATTENTION : LA LAMPE SOUS

ATTENTION CHAUD :

HAUTE PRESSION PEUT SI ELLE, N'EST

DEBRANCER LE CORD ON

PAS MANIPULEE CORRECTEMENT,

D'ALOMENTION ET ATENDER

CONFIER L'OPERATION A UN

60 MINUTES AVANT DE

PERSONNEL D'ENTRETIEN QUALIFIE.

CHANGER LAMPE.

Caution Concerning the Setup of the Projector

For minimal servicing and to maintain high image quality, avoid humidity, dust and cigarette smoke.

When the projector is subjected to these environments,the lens and part of ventilation holes must be cleaned more often than usual. As long as the projector is properly maintained in this manner, use in these environments will not reduce the overall operation life. Please note that all internal cleaning must be performed by an Marantz Authorized Dealer, or Service Center.

•Do not expose the projector to extreme heat or cold. Operating temperature:41 °F to 95 °F (+5 °C to 35 °C) Storage temperature:–4 °F to 140 °F (–20 °C to +60 °C)

Notes on Operation

•The exhaust ventilative hole, the lamp cage cover and adjacent areas may get extremely hot during projector operation. To prevent injury,do not touch these areas until they have sufficiently cooled down.

•Allow at least 1 foot (30 cm)of space between the exhaust ventilative hole and the nearest wall or obstruction.

•If the cooling fan becomes obstructed, a protection device will automatically turn off the projector lamp. This does not indicate a malfunction. Remove the projector power cord from the wall outlet and wait at least 10 minutes.

Then turn on the power by plugging the power cord back in. This will return the projector to the normal operating condition.

95˚F

(+35˚C)

41˚F

(+5˚C)

1

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model VP-12S3/VP-12S3L User Guide For the customers in the USA Important Safety Instructions Lamp Handing Precautions Precauciones para la manipulación de la lámpara Table of Contents Replacement Important SafeguardsEasy to install and operate FeaturesDesigned for silence and safety Lens Cap x Remote Controller x AccessoriesProjection Lens IR sensor Front and Top ViewBottom View Rear and Terminals ViewTerminals TerminalsInput Remote ControllerPreparing the Remote Controller Remote Controller Operational RangeConnection When making connections be sure toWhen pulling out a cable Connection with AC Power SupplyAdvanced Connection Connection with a HD-Video, Satellite, Cable Tuner or PCAdjusting the Image Position Initial SettingTurning on the Power Zooming and FocusingCounterclockwise Down Adjusting the HeightDetail Focusing Returning the Projector to its Initial PositionKeystone Correction Mounting on the ceiling InstallationRecommended Setting Installing on a tabletop16 9 Screen Screen Size and Projection Distance inch VP-12S3Screen Diagonal Width Height Minimum Maximum Inch Screen Size and Projection Distance m VP-12S319 5/8 78 9/16 107 1/16 Screen Size and Projection Distance inch VP-12S3LMinimum Maximum Screen Size and Projection Distance mm VP-12S3LSelecting the Aspect Mode Selecting the Input Signal SourceBasic Operations Screen Images in a 169 screen Screen Images in a 43 screen To Turn off the Power Menu Structure OperationsPicture Mode and Memory How to Operate MenusPicture mode Index Contrast Picture AdjustColor Temp. Temperature Setting the Picture Adjust MenuChrominance DelayFine Menu LuminanceMiscellaneous Sub ControlSetting the Setting Menu Setting2-2 pull down for PAL System Setting the System MenuDisplay Setting the Display MenuOSD Position 169 ConfigurationAuto Power Off Reset Lamp LifeOn Output DC Off No output Setting the Config MenuSetting the Trigger 2 Menu TriggerGamma setting PresetSetting the Preset Menu Memorizing settings in an indexTo clear the warning, p ss the Menu button MaintenanceLamp Life and Replace Lamp Lamp LifeInitialize the Lamp Life How to replace the Lamp UnitReplacing Lamp Unit English When installed on a tabletop Color Temperature AdjustmentWhen installed on a ceiling Optional Accessories Color Temperature Sensor ProtectionCleaning the Lens Replacement PartsTroubleshooting On Screen Message Error ModeInput/Output SpecificationsOptical characteristics AccessoriesKHz Scan Timing chartRear DimensionsFront BottomKeystone Black Level Black setupGlossary Aspect ratioIs a registered trademark
Top Page Image Contents