Lucent Technologies PA-8500 manual T800-Series Parts Stand-Alone Tape Drive

Page 40

	Chapter 3
	Part Number	Description
	AA-T80500	T800-Series Tape Drive
	AA-T80600	T800-Series Tape Drive
	AA-T80600
	AW-B12800- XX	Power Cord
	AW-B21000-12	SCSI Cable
	JC-005TRM	SCSI Terminator
	AX-T60007	Data Cartridge (T805 and T806)
	AX-T60006	Autoloader magazine (T806)
	AX-T60002	Cleaning Cartridge (T805 and T806)

Parts included with the Stand-Alone T800-Series Tape Drive. (See Figure 3.1)

Figure 3.1. T800-Series Parts: Stand-Alone Tape Drive

2.Place the tape drive on a table or rack near the rear of the system cabinet.

Image 40

Contents Revision 0.0 5/5/00 Copyright 2000 Lucent Technologies. All Rights Reserved Manual Conventions Preparing to Install the System Preparing to Install the System 3a.1 Dncp Series 400 PA-8500 Cabinet 3a.1.1 Dncp Series 400 PA-8500 Cabinet Front Components Dncp Series 400 PA-8500 Cabinet Front View3a.1.2 Dncp Series 400 PA-8500 Cabinet Rear Components Dncp Series 400 PA-8500 Cabinet Rear View3a.1.3 System Ventilation System Ventilation3b System Description for Dncp Series 400-CO PA-8500 3b.1.1 Dncp Series 400-CO PA-8500 Cabinet Front Components Dncp Series 400-CO PA-8500 Cabinet Front View3b.1.2 Dncp Series 400-CO PA-8500 Cabinet Rear Components Dncp Series 400-CO PA-8500 Cabinet Rear View Status Lights 3b.1.3 System VentilationV105 Terminal C419/C619 ModemTape and CD-ROM Drives Installing the Core System Components Removing the Cable Opening Cover Attaching the Ground Cable Top of cabinet Connecting the Power Cables Top Entry 1b Installing the Cabinet For Dncp Series 400-CO PA-8500 Cabinet Grounding Wires and Main Power Switches Attaching the Ground Cable Bottom of Cabinet 1b.1 Installing the Power Cables Top Entry Connecting the Power Cables Top Entry 10. DC Connector Cable/Cabinet End 1b.2 Installing the Power Cables Bottom EntryChapter Installing the System Console 13. Connecting the Keyboard to 14. Connecting the V105 Power Cord 16. V105 Operating Dials Installing a C419/C619 Modem for RSN Use 20. Modem DIP Switch Settings 21. Connecting the Modem Telephone Cable 23. Connecting the RS-232 Cable to the System 24. Connecting the Modem Power Cord Installing PCI Cards and Cables Installing Tape Drives Sbin/hwmaint stop vsb n Items Included with Stand-Alone T800-Series Tape DrivesT800-Series Parts Stand-Alone Tape Drive Scsi Identification Display Stand-Alone T800-Series Powering Down the T800-Series T800-Series Power Cord Powering Up the T800-Series Items Included with Daisy-Chained T800-Series Tape Drives T800-Series Parts Daisy-Chained Tape DriveScsi Identification Display Daisy-Chained T800-Series 10. Scsi Terminator Daisy-Chained T800-Series 12. Scsi Cables Daisy-Chained T800-Series 13. T800-SeriesPower Cord 2nd 14. Powering Up the T800-Series 2nd Sbin/hwmaint start vsb n Booting the System Logic Suitcase Power-Up Light Sequence Power-UpStage Color State MeaningInit Single User Mode Chapter Configuring the RSN and C419/C619 Modem Usr/stratus/rsn/bin/rsnon Rsnadmin Main Menu Bridge System Path Menu SITE-ID compux Siteinfo Menu Return to Siteinfo Menu Configuring the C419/C619 Modem Completing and Verifying Configuration of the RSN Checking RSN Inittab Settings Usr/stratus/rsn/bin/rsntry Sending the Installation Report Lucent Technologies Cabinet Part Number and Serial Number Beth Smith Installation went well. your name Return Sending an Installation Report to the CAC Saving the Installation Report to a Temporary File Chapter Scsi ACU P271 Disk Power Cab 0 dps P274 Main breaker Cab 0 mps Appendix a Fault Isolation System Component LEDs Power Supply LEDs Disk Shelf LEDs PCI Card LEDs System Log and Status Messages Component Status Fault Codes Liteok Missng Troubleshooting Procedures Troubleshooting Flow