Lucent Technologies PA-8500 manual Installing the Core System Components

Page 17

Chapter 2

Chapter 2

Installing the Core System Components

After unpacking the system, follow the instructions in this chapter to install the core system components. The core system components consist of the cabinet, V105 terminal, C419/C619 modem, and PCI cards. This chapter contains the following sections.

Installing the Cabinet

Installing the System Console

Installing a C419/C619 Modem for RSN Use

Installing PCI Cards and Cables

The information in this chapter assumes that the system site has been prepared according to the instructions in the DNCP Series 400/400-CO: Site Planning Guide (R454) and unpacked according to the instructions in the DNCP Series 400/400-CO(PA-8500): Unpacking Instructions.

2.1a Installing the Cabinet -- for DNCP Series 400 (PA-8500)

Install the cabinet by performing the steps in the following sections:

If routing the power cables from the top of the cabinet, perform the following steps (See Section 2.1a.1 Installing the Power Cables (Top Entry).

If routing the power cables from the bottom of the cabinet, perform the following steps (See Section 2.1a.2 Installing the Power Cables (Bottom Entry).

2.1a.1 Installing the Power Cables (Top Entry)

Perform the following steps to route the power cables from the top of the system.

1.Open the cabinet doors.

2.Verify that the cabinet ground wires are connected from the cabinet frame to the doors.

3.Make sure that the two MAIN power switches/AC Input breakers on the front of the cabinet are in the off (0) position. (See Figure 2.1)

Figure 2.1. Cabinet Grounding Wires and MAIN Power Switches/AC Breaker

]

Image 17
Contents Revision 0.0 5/5/00 Copyright 2000 Lucent Technologies. All Rights Reserved Manual Conventions Preparing to Install the System Preparing to Install the System 3a.1 Dncp Series 400 PA-8500 Cabinet Dncp Series 400 PA-8500 Cabinet Front View 3a.1.1 Dncp Series 400 PA-8500 Cabinet Front ComponentsDncp Series 400 PA-8500 Cabinet Rear View 3a.1.2 Dncp Series 400 PA-8500 Cabinet Rear ComponentsSystem Ventilation 3a.1.3 System Ventilation3b System Description for Dncp Series 400-CO PA-8500 Dncp Series 400-CO PA-8500 Cabinet Front View 3b.1.1 Dncp Series 400-CO PA-8500 Cabinet Front Components3b.1.2 Dncp Series 400-CO PA-8500 Cabinet Rear Components Dncp Series 400-CO PA-8500 Cabinet Rear View 3b.1.3 System Ventilation Status LightsC419/C619 Modem V105 TerminalTape and CD-ROM Drives Installing the Core System Components Removing the Cable Opening Cover Attaching the Ground Cable Top of cabinet Connecting the Power Cables Top Entry 1b Installing the Cabinet For Dncp Series 400-CO PA-8500 Cabinet Grounding Wires and Main Power Switches Attaching the Ground Cable Bottom of Cabinet 1b.1 Installing the Power Cables Top Entry Connecting the Power Cables Top Entry 1b.2 Installing the Power Cables Bottom Entry 10. DC Connector Cable/Cabinet EndChapter Installing the System Console 13. Connecting the Keyboard to 14. Connecting the V105 Power Cord 16. V105 Operating Dials Installing a C419/C619 Modem for RSN Use 20. Modem DIP Switch Settings 21. Connecting the Modem Telephone Cable 23. Connecting the RS-232 Cable to the System 24. Connecting the Modem Power Cord Installing PCI Cards and Cables Installing Tape Drives Items Included with Stand-Alone T800-Series Tape Drives Sbin/hwmaint stop vsb nT800-Series Parts Stand-Alone Tape Drive Scsi Identification Display Stand-Alone T800-Series Powering Down the T800-Series T800-Series Power Cord Powering Up the T800-Series T800-Series Parts Daisy-Chained Tape Drive Items Included with Daisy-Chained T800-Series Tape DrivesScsi Identification Display Daisy-Chained T800-Series 10. Scsi Terminator Daisy-Chained T800-Series 12. Scsi Cables Daisy-Chained T800-Series 13. T800-SeriesPower Cord 2nd 14. Powering Up the T800-Series 2nd Sbin/hwmaint start vsb n Booting the System Power-UpStage Color State Meaning Logic Suitcase Power-Up Light SequenceInit Single User Mode Chapter Configuring the RSN and C419/C619 Modem Usr/stratus/rsn/bin/rsnon Rsnadmin Main Menu Bridge System Path Menu SITE-ID compux Siteinfo Menu Return to Siteinfo Menu Configuring the C419/C619 Modem Completing and Verifying Configuration of the RSN Checking RSN Inittab Settings Usr/stratus/rsn/bin/rsntry Sending the Installation Report Lucent Technologies Cabinet Part Number and Serial Number Beth Smith Installation went well. your name Return Sending an Installation Report to the CAC Saving the Installation Report to a Temporary File Chapter Scsi ACU P271 Disk Power Cab 0 dps P274 Main breaker Cab 0 mps Appendix a Fault Isolation System Component LEDs Power Supply LEDs Disk Shelf LEDs PCI Card LEDs System Log and Status Messages Component Status Fault Codes Liteok Missng Troubleshooting Procedures Troubleshooting Flow