Lowrance electronic Fish Finder manual Insert bolt and check transducer position on transom

Page 14

Reassemble the transducer and bracket and place them against the transom. Again, check to see if you can move the transducer so it's parallel with the ground. If you can, then go to step 3. If it doesn't, repeat step 2, but use a different alignment letter until you can place the transducer on the transom correctly.

Ratchets

Insert bolt and check transducer position on transom.

3.Assembling the transducer. Once you determine the correct posi- tion for the ratchets, assemble the transducer as shown in the follow-

ing figure. Don't tighten the lock nut at this time.

Metal

Nut washer

Rubber	Metal washer
washers	Metal washer
	Bolt

Assemble transducer and bracket.

4.Drilling mounting holes. Hold the transducer and bracket assembly against the transom. The transducer should be roughly parallel to the ground. The transducer's centerline should be in line with the bottom of the hull. Don't let the bracket extend below the hull!

Mark the center of each slot for the mounting screw pilot holes. You will drill one hole in the center of each slot. Drill the holes using the #29 bit (for the #10 screws).

12

Image 14

Contents M52 Pro Visit our web site Table of Contents Split Zoom Sonar Chart Index Page Sonar GeneralBack-up memory Sonar soundingGPS How to use this manual typographical conventionsGraphic symbols for Waypoints or event Receiver/antennaTransducer Installation PreparationsRecommended Tools and supplies Selecting a Transducer LocationHow low should you go? Shoot-thru-hull vs. Transom Mounting Transom Transducer Assembly and Mounting Insert bolt and check transducer position on transom Transom Trolling Motor Bracket Installation Transducer Orientation and Fish Arches Hulls With Floatation Materials Testing Determines Best LocationSHOOT-THRU-HULL Preparation Transducer location High speed Trolling speed Shoot-thru-hull Installation Power and Cable Connections Page In-Dash Installation Mounting the Sonar Unit In-Dash or BracketBracket Installation 107.5 82.7 156 Depress ratchets to Release. Swivel base Portable Sonar Installation Installing the BatteriesPortable transducer installed on boat transom Section Basic Sonar Operation KeyboardMain Menu Sonar Menu Commands Sonar MenuBasic Sonar Quick Reference Pages Sonar Operations Fish Symbols vs. Full Sonar Chart Important TipPage Alarms ASP Advanced Signal ProcessingZone Alarm Press MENUMENU↓ to ALARMSENT↓ to Sonar AlarmsentFish Alarm Chart Speed Depth CursorDepth Range Automatic Depth Range ManualDepth Range Upper and Lower Limits Fish I.D. Fish Symbols & Depths FasTrackFishTrack Grayline→Overlay Data Ping Speed & HyperScroll Automatic Sensitivity Reset OptionsSensitivity & Auto Sensitivity Keel and Waterline Offset Keel OffsetFull Sonar Chart Sonar Color ModeSonar Chart Display Options Waterline OffsetDigital Data/Chart Split Zoom Sonar ChartFlasher Pro TipsSonar Simulator Zoom & Zoom Bar Stop ChartSurface Clarity Zoom PanUnit freezes, locks up, or operates erratically Unit operates only in demo modeUnit wont turn on No fish arches when the Fish I.D. feature is off NoiseSection Basic GPS Operations Main MenuSonar Pages Satellite StatusNavigation Page Position PlotterViewing the Plotter Zoom & Cursor Arrow Keys Selecting Any Plotter Item With the Cursor Navigate to Cursor Position on PlotterGPS Quick Reference Waypoints Cancel NavigationFind Distance between Points Create a WaypointPress WPT↓ to Create Newent Delete a Waypoint Select a Waypoint Find a WaypointEdit a Waypoint Navigate To a Waypoint Set Man Overboard MOB Waypoint Creating and Saving a Trail Navigate Back to MOB WaypointTrails Tip Edit a Trail Name Delete a TrailDisplay a Saved Trail Navigate a Trail forward Navigate a TrailVisual Trailing Page Navigate a Back Trail Create Icon at Current Position IconsCreate Icon on Plotter Delete an IconCreate and Save a Route RoutesNavigate to an Icon Page Delete a Route Edit a Route NameNavigate a Route Navigate a Route backward Utilities Page Section System & GPS Setup Options Important Alarm Notes Auto Satellite SearchCoordinate System Selection Map Fix Customize Position Customize Page DisplaysGPS Simulator Customize Plotter or NavigationPlotter Auto Zoom Hide GPS FeaturesInitialize GPS Plotter Orientation From the Plotter or Sonar page, press MENU↓ Position Pinning Pop-up HelpScreen Contrast and Brightness Set Local Time Show Waas AlarmSet Language Sounds and Alarm Sound Styles Software Version InformationDelete All Trails Track SmoothingTrail Options Main Menu, left, Trails Menu, center, Trail Options, right New Trail Units of MeasureDelete Trail Trail Visible/Invisible and Other Trail OptionsMain Menu, left, Units of Measure Menu, right Index Page Page 100 Navico Databases License Agreement Databases Limited Warranty Navico Full ONE-YEAR Warranty How to Obtain Service… Not toll-freeAccessory Ordering Information for all countries Visit our web site