Honda Power Equipment T32, T38, T27 Models T25 AE1, T30 AE1, T35 AE1, T40 AE1 aluminum decks

Page 25

om_T40_2006_D-GB-F.book Page 25 Jeudi, 29. juin 2006 4:03 16

ASSEMBLY

Do not use a compressed air source (ex.: air compressor) to inflate the boat. Overinflation may cause the seams and/or walls themselves to rupture.

MODELS T25 AE1, T30 AE1, T35 AE1, T40 AE1 (aluminum decks)

CAUTION:

•Do not inflate the keel until the floor is in place. 1. Unfold the boat on a flat, clean surface.

2.Check that the valves [1] are in place. Check that they all have their cap [2] held by a retainer [3].

3.First use: using the foot pump supplied with your boat, inflate the floaters completely, being careful to balance the pressure between the various chambers. Once fully inflated, deflate the chambers half way by pressing the yellow push-button [4] at the centre of each valve.

Subsequent uses: using the foot pump supplied with your boat, inflate the chambers to half their capacity.

NOTE: The floor elements must be installed so that their identification number is visible.

4.First insert floor element no. 1 in the bow of the boat.

5.Insert floor element no. 4 (no. 3 for the T25 AE1) in the transom [5] of the boat.

6.Insert floor element no. 2 into no. 1.

7.T25 AE1: Insert floor element no. 2 into no. 3 and press down the assembly to flatten the deck [6].

Other models: Insert floor element no. 3 into elements no. 2 then no. 4 and press down the assembly to flatten the deck [6].

MONTAGE

Ne pas utiliser de source à air comprimé (ex : compresseur) pour gonfler le bateau. Un surgonflage peut entraîner la rupture des coutures et/ou des parois.

MODÈLES T25 AE1, T30 AE1, T35 AE1, T40 AE1 (planchers aluminium)

PRÉCAUTION:

•Ne pas gonfler la quille avant d’avoir mis le plancher en place. 1. Déplier le bateau sur une surface plane et propre.

2.Vérifier que les valves [1] soient bien en place. Vérifier qu’elles aient toutes leur capuchon [2] retenus par une garcette [3].

3.Première utilisation : à l’aide du gonfleur à pied fourni avec votre bateau, gonfler les flotteurs entièrement, en prenant soin de maintenir une pression équilibrée entre les différentes chambres. Une fois gonflé entièrement, dégonfler les chambres à moitié en appuyant sur le poussoir jaune [4] situé au centre de chaque valve.

Utilisations suivantes : à l’aide du gonfleur à pied fourni avec votre bateau, gonfler les chambres à moitié de leur capacité.

NOTE : Les planches doivent-être montées de telle sorte que leur numéro d’identification soit visible.

4.Insérer d’abord la planche n°1 dans l’étrave du bateau.

5.Insérer la planche n°4 (n°3 pour le T25 AE1) dans le tableau arrière [5] du bateau.

6.Insérer la planche n°2 dans la n°1.

7.T25 AE1 : Insérer la planche n°2 dans la n°3 et presser l’ensemble pour aplatir le plancher [6].

Autres modèles : Insérer la planche n°3 dans les planches n°2 puis n°4 et presser l’ensemble pour aplatir le plancher [6].

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents T20 T24 T25 T27 T30 T32 T35 T38 T40 Verwendung InhaltsverzeichnisContents Description Générale Tables DES MatièresEnvironmental Protection UmweltschutzProtection DE L’ENVIRONNEMENT Ausbildung SicherheitshinweiseVorbereitung Navigation EnergieversorgungInstandhaltung UND Lagerung Training Safety InstructionsPreparation Refuelling Maintenance and StorageFormation Consignes DE SécuritéPréparation Ravitaillement Maintenance ET StockageSiehe Tabelle auf Seite EinführungDescription of the Codes Used in this Manual IntroductionSee table, p Explication DES Codes Utilisés Dans CE ManuelKennzeichnung DES Boots Teile DES BootsAllgemeine Beschreibung Description Générale General DescriptionAuspacken Der Verpackung des Boots sind enthaltenDéballage UnpackingDOPPELDRUCK-BLASEBALG T24 IE1, T27 IE1, T32 IE1 und T38 IE1 LuftpumpenGonfleurs Foot PumpsTWO-PRESSURE Pump T24 IE1,T27 IE1, T32 IE1 and T38 IE1 Gonfleur Standard sauf T24 IE1, T27 IE1, T32 IE1 et T38 IE1Modelle T20 SE1, T25 SE1 Lattenboden MontageModels T20 SE1, T25 SE1 slatted flooring AssemblyModèles T20 SE1, T25 SE1 planchers lattés Modelle T24 IE1,T27 IE1, T32 IE1, T38 IE1 aufblasbarer Boden OmT402006D-GB-F.book Page 23 Jeudi, 29. juin 2006 403 Den Kiel nicht vor dem Einsetzen des Bodens aufblasen Modelle T25 AE1, T30 AE1, T35 AE1, T40 AE1 AluminiumbodenModels T25 AE1, T30 AE1, T35 AE1, T40 AE1 aluminum decks 35 bar 25 bar OmT402006D-GB-F.book Page 27 Jeudi, 29. juin 2006 403 Belastung VerwendungNavigationsbereich Navigation MIT DEN PaddelnUtilisation USEAbschleppen AnlegenFestmachen , Ankern Lecks Während DER NavigationTowing DockingMOORING, Anchoring Puncture While UnderwayReinigen WartungshnweiseZerlegen Entretien MaintenanceKleine Reparaturen ReparaturenGrosse Reparaturen Réparations RepairLagerung Transport LagerungTransport Stockage Transport StorageStorage StockageSE1 AE1 IE1 Technische DatenVIB Technical Specifications

T27, T25, T20, T32, T24 specifications

Honda Power Equipment offers a diverse line of products designed for efficiency and convenience, catering to both residential and commercial users. Among its notable models are the T35, T38, T24, T32, and T20, each tailored to deliver optimal performance in various applications, from landscaping to outdoor maintenance.

The T35 model stands out with its powerful engine, capable of delivering high torque for efficient cutting and trimming. Its lightweight design enhances maneuverability, making it ideal for extended use without causing fatigue. The T35 also features a semi-automatic feed system, allowing users to operate it with minimal interruptions, ensuring a smooth workflow.

Similarly, the T38 offers increased power and versatility. This model is equipped with advanced anti-vibration technology, which reduces user fatigue during prolonged sessions. The T38 boasts a 4-stroke engine, providing better fuel efficiency compared to 2-stroke alternatives. Its larger cutting swath allows users to cover more ground quickly while maintaining precision.

Next in line, the T24 is perfect for lighter trimming tasks. It is crafted for ease of use, making it an excellent choice for homeowners and small business operators. The T24’s compact size does not compromise its performance, featuring a reliable engine that ensures effective cutting of grass and weeds. The machine is also fitted with intuitive controls, making it accessible for users of all skill levels.

The T32 model combines versatility with power, striking a balance suited for both residential and commercial applications. Its adjustable cutting head allows users to tackle various jobs, from hedging to thick brush clearing. The T32 integrates Honda’s innovative fuel-efficient technology, which minimizes emissions and operating costs, making it an environmentally friendly choice.

Finally, the T20 represents the entry-level option, ideal for casual users and gardeners. Despite its smaller build, the T20 incorporates Honda's reputable quality and reliability. Its easy-start mechanism and lightweight design facilitate quick setup and use, enabling users to focus on the task at hand without hassle.

Overall, Honda’s T-series models embody innovation, efficiency, and user-friendly features, establishing themselves as essential tools in the realm of power equipment. With each model offering specific advantages, users can find the right fit for their unique needs and preferences.
Top Page Image Contents