Baja Marine 40 manual Gear case

Page 48

Section 4 • Bilge & Underwater Gear

f.Install the thrust washer, propeller, continuity washer, thrust hub, propeller nut retainer and the propeller nut onto the shaft (Figure 4.3.3).

g.Place a block of wood between the gear case and the propeller (Figure 4.4.1) and torque the propeller nut to recommended manufacturer’s specifications. The correct propeller nut torque is given in your Engine Operator’s Manual in the Owner’s Manual Packet.

Propeller

 

(Fig. 4.4.1)

gear case

 

wood block

h.Secure the propeller nut by bending three (3) of the tabs of the propeller nut retainer into the thrust hub grooves (Figure 4.4.2).

Propeller

(Fig. 4.4.2)

securing tabs

4.4

40 Outlaw®

Image 48
Contents Baja Marine OutlawFor information call 1-865-971-6270 or fax Welcome This page intentionally left blank Introduction Service, Parts and Repair for Your Boat Hull Identification Number HINManufacturer’s Certification About Your Express Limited Warranty Iii Ignition Protection Breakers and/or Fuses Speed changes you. TM Safety Safety LabelsLegally Mandated Minimum Required Equipment Fire Extinguishing SystemCarbon Monoxide Carbon Monoxide Monitor Lifesaving Equipment Additional Recommended Equipment for Safe Operation Impaired OperationPower Capacity Load CapacityPropellers United StatesStability Maintain ControlChart Your Course WeatherGeneral Considerations Water Sports SwimmingSkiing Emergency Situations GeneralMedical Emergency Water RescueFire Flooding, Swamping and CapsizingSafety Hotlines Collisions and LeakingGrounding Propulsion, Control or Steering FailureInternational Requirements Environmental ConsiderationsFuel and Oil Spillage Waste Disposal Wake/WashExcessive Noise Nautical Terms Key to Symbols on Controls & Prints Baja Marine Corp This Page Intentionally Left Blank General Boat Arrangement Docking /Lifting /Trailering Passenger Locations2 Hull Basic Boat Dimensions and Clearances Metric Propulsion SystemGeneral Deck Layout General Deck Layout FIGPower Trim Unit and Gauge Description of Major ControlsGear Shift and Throttle Control Trailer Switch Trim TabsIgnition Shutdown Switch Engine Alarm SystemImportant Gauges Tachometer and Hour MeterOil Pressure, Water Temperature, Voltmeter and Fuel Gauges Navigation and Anchor LightsUsing Your Boat Pre-Launch, Launch and Post- Launch ChecklistTrailer Launching and Loading Fueling the BoatBoarding Personal Flotation DevicesPassenger Instruction and Location Starting the EngineShifting to Drive the Boat Stopping the EngineSteering Systems Hydraulic SteeringPower Steering Power Steering SystemThis page intentionally left blank Bilge & Underwater Gear BilgeFuel & Oil Spillage Drain PlugMaintenance and Service Engines and Stern DriveBilge Blowers Vibration and CausesPropeller Removal and Installation Impact to Stern DriveGear case Fuel System Fuel SystemAnti-Siphon Valve Inboard/Outboard Engine Only Fueling Precautions Before and During Fueling ChecklistStatic Electricity and the Fuel System After Fueling Checklist This page intentionally left blank Electrical Systems Electrical SystemsDirect Current DC BatteriesElectrolytic Corrosion & Zinc Anodes Breakers and/or FusesFuse Panel Marine Electronic Cathodic Anti-corrosion System Mercathode Ignition Switch Drive Pump with K-Plane Trim Tabs FIG Switch Panel Wire Information Triple FIG Switch Panel Wire Information Twin FIG Wiring Harness Information FIG DC Distribution Wiring Information FIG Hull Wiring Harness Information FIG Gauge Panel Wiring Information FIG Breaker Panel Wiring Information FIG Options & Accessories Options & Accessories LocationsAutomatic Fire Extinguisher System Option Fire Extinguisher PortCanvas Canvas Care and Maintenance Swim Platform w/ Ladder OptionalDepth Finder Optional HornStereo System Head SystemsPortable Head with Pump-Out Requirements for OperatorsExhaust Systems VacuFlush Head OptionHolding Tank Operation Vent FilterThis page intentionally left blank Required Inspection, Service Maintenance Summary Guide for Inspection, Service and MaintenanceInterval Summary Guide For Inspection, Service and Maintenance IntervalUseful Service Information Inspection, Service and Maintenance Protocol Bilge AreaWinterization Checklist for Boats Stored on Land BatteryiesTopside and Supplies Boat StorageFitting Out After Storage Fuel SystemsFuel System MiscellaneousPower Steering System Maintenance Security ConsiderationsQuick Reference Checklist Boarding the Boat GeneralBoat Systems Starting the Engine Quick Reference Checklist cont’d Departing General Returning to Port GeneralQuick Reference Checklist cont’d Securing the BoatIf the Engine Does Not Start After Market Equipment Checklist Maintenance Log Maintenance Log Cont’d Paint Cleaning Agents & Other Substances Care & RefinishingStains & Scratches Fiberglass & GelcoatPermanently Moored or Docked Boats Topside AreasAcrylic Plastic Sheeting Plastic Glass Canvas and Clear VinylExterior Upholstery Fabric Interior Upholstery FabricThis Page Intentionally Left Blank Index Index Outlaw