Pioneer DJM-800 operating instructions Midi Settings, Midi Messages, Midi Channel Setting

MIDI SETTINGS

MIDI SETTINGS

MIDI is an acronym for “Musical Instrument Digital Interface” and refers to a protocol developed for the exchange of data between electronic instruments and computers.

A MIDI cable is used to connect components equipped with MIDI connectors to enable the transmission and receipt of data.

The DJM-800 uses the MIDI protocol for transmitting and receiving data about component operation and BPM (timing clock).

DJ CD Player
			MIDI sequencer
OUT	BPM		IN
Audio	=120	BPM
IN		=120	MIDI OUT
			MIDI START
			/STOP
			TIME
DJM-800

SYNCHRONIZING AUDIO SIGNALS TO EXTERNAL SEQUENCER, OR USING DJM-800 INFORMATION TO OPERATE AN EXTERNAL SEQUENCER

1.Use a commercially available MIDI cable to connect the DJM-800’s MIDI OUT connector to the MIDI sequencer’s MIDI IN connector.

¶Set the MIDI sequencer’s synch mode to “Slave”.

¶MIDI sequencers that do not support MIDI timing clock cannot be synchronized.

¶Synch may not be achieved if the track’s BPM cannot be detected and measured stably.

¶BPM values set with the TAP mode can also be used to output the timing clock.

2.Press the MIDI START/STOP button.

¶The MIDI timing clock output range is 40 to 250 BPM.

Note:

¶Accurate measuring of BPM may be impossible with some tracks.

[MIDI Channel Setting]

The MIDI channel (1 to 16) can be set and stored in memory.

1.While holding the MIDI START/STOP button depressed, set the power switch to ON.

¶The display will show [MIDI CH SETTING] and the unit will enter the MIDI setting mode.

2.Rotate the TIME dial to select the MIDI channel.

3.Press the MIDI START/STOP button.

¶The selected MIDI channel will be recorded.

4.Set power to OFF.

English

MIDI MESSAGES

Category	Switch Name	Switch Type			MIDI Message		Comments
				MSB		LSB
CH1	TRIM	VR	Bn	01	dd		0 to 127
	HI	VR	Bn	02	dd		0 to 127
	MID	VR	Bn	03	dd		0 to 127
	LOW	VR	Bn	04	dd		0 to 127
	COLOR	VR	Bn	05	dd		0 to 127
	CUE	BUTTON	Bn	46	dd		OFF=0, ON=127
	FADER	VR	Bn	11	dd		0 to 127
	CF ASSIGN	SW	Bn	41	dd		0, 64, 127
CH2	TRIM	VR	Bn	06	dd		0 to 127
	HI	VR	Bn	07	dd		0 to 127
	MID	VR	Bn	08	dd		0 to 127
	LOW	VR	Bn	09	dd		0 to 127
	COLOR	VR	Bn	0A	dd		0 to 127
	CUE	BUTTON	Bn	47	dd		OFF=0, ON=127
	FADER	VR	Bn	12	dd		0 to 127
	CF ASSIGN	SW	Bn	42	dd		0, 64, 127
CH3	TRIM	VR	Bn	0C	dd		0 to 127
	HI	VR	Bn	0E	dd		0 to 127
	MID	VR	Bn	0F	dd		0 to 127
	LOW	VR	Bn	15	dd		0 to 127
	COLOR	VR	Bn	16	dd		0 to 127
	CUE	BUTTON	Bn	48	dd		OFF=0, ON=127
	FADER	VR	Bn	13	dd		0 to 127
	CF ASSIGN	SW	Bn	43	dd		0, 64, 127

19

<DRB1394> En