CONNECTIONS (CONNECTION PANEL)
CONNECTIONS
CONNECTION PANEL
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|
|
|
| SIGNAL GND |
|
|
|
|
|
| SIGNAL GND |
|
|
|
| DIGITAL IN |
| |
| MASTER 2 | REC | PHONO | LINE | PHONO | LINE |
|
| PHONO | CD | LINE | L | CD |
|
|
|
| |
| L |
|
| L |
| L |
|
|
| L |
|
|
|
|
|
|
| |
POWER |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
OFF | ON |
|
| CONTROL |
|
| CONTROL |
|
| CONTROL |
|
| CONTROL |
|
| MIDI OUT | ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| 1GND |
|
| R |
| R |
|
|
| R |
|
| R |
|
| DIGITAL OUT |
| |
| R |
|
|
|
|
|
|
|
|
|
| fs (Hz) |
| |||||
| 2HOT |
|
| DIGITAL |
|
| DIGITAL |
|
|
| DIGITAL |
|
| DIGITAL |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
AC IN | 3COLD |
|
| LINE |
|
| LINE |
|
|
| CD |
|
| CD | 48 k | 96 k |
| |
|
|
| MASTER ATT |
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| R | MASTER 1 L | ADD | CUT |
| R | BOOTH | L | R | SEND L(MONO) | R | RETURN L(MONO) |
|
|
| |||
| MIC SIGNAL |
|
|
|
| |||||||||||||
|
|
|
|
| (TRS) |
|
|
| ||||||||||
21 |
|
| 20 | 19 | 18 | 17 |
| 16 | 15 | 14 | 13 | 12 | 11 | 10 | 9 | |||
1.POWER switch
2.MASTER 2 output connectors
RCA type unbalanced output.
3. Recording output connectors (REC)
RCA type output connectors for recording.
4. PHONO input connectors
RCA type phono level (MM cartridge) input connectors. Do not use for inputting line level signals.
5. LINE input connectors
RCA type line level input connectors.
Use to connect a cassette deck or other line level output component.
6. Signal grounding terminals (SIGNAL GND)
Use to connect ground wires from analog players.
This is not a safety grounding terminal.
7. CD input connectors
RCA type line level input connectors.
Use to connect a DJ CD player or other line level output component.
14. SEND output connectors
Ø6.3 mm
Use to connect to the input connectors of external effectors or other similar components. When the L channel only is connected, a L+R monaural signal is output.
15. CONTROL connectors
Ø3.5 mm
When the connectors are connected, the
16. BOOTH monitor output connectors
Ø6.3 mm
The sound level from these connectors is controlled independently by the BOOTH MONITOR level dial, regardless of the position of the MASTER LEVEL dial. (These connectors are TRS output, so they support both balanced and unbalanced outputs.)
17. DIGITAL/LINE input selector switches
Use to select either analog input (LINE) or digital input (DIGITAL IN).
8. DIGITAL IN connectors
RCA type digital coaxial input connectors.
Use to connect to DJ CD player or other digital coaxial output connectors.
9. MIDI OUT connector
DIN type output connector.
Use to connect to other MIDI component (see P. 19).
10. DIGITAL OUT connector
RCA type digital coaxial output connector.
Master audio digital output.
11. Sampling frequency selector switch (fs 48 k/96 k)
Use to set the sampling frequency of the digital output to 96 kHz/24-
bit or 48
12. DIGITAL/CD input selector switches
Use to select either analog input (CD) or digital input (DIGITAL IN).
13. RETURN connectors
Ø6.3 mm
Use to connect to the output connectors of external effectors or similar components.
When the L channel only is connected, the L channel input is simultaneously input to the R channel.
18. Master output attenuator switch (MASTER ATT)
Use to attenuate the level of the master 1 and master 2 outputs. Selectable values are 0 dB,
19. Microphone signal switch
(MIC SIGNAL ADD/CUT)
When set to the [ADD] position, the sounds from microphone 1 and microphone 2 are output to the BOOTH monitor output connectors. When set to the [CUT] position, the sounds from microphone 1 and microphone 2 are not output to the BOOTH monitor output connectors.
20. MASTER 1 output connectors
XLR type (male) balanced output.
÷When using a cord with
21. Power inlet (AC IN)
Use the accessory power cord to connect to an AC power outlet of the proper voltage.
4
<DRB1394> En