Hughes & Kettner Comprehensive Guide to Techniques and Features of Attax 80

Page 10

ATTAX-MANUAL

7)You have connected the RECORDING OUT jack to a mixing console, but you find it doesn't deliver the sound you had in mind.

The RECORDING OUT circuit is dual-purpose. It is also designed to allow you to feed its signal to an additional power amp and cabinet. For absolutely top-notch professio- nal recording purposes, route the signal through a Hughes & Kettner REDBOX before patching it to a mixing console.

7.0 TECHNICAL DATA

PREAMP SECTION:	CLEAN + LEAD solid state channels
INPUT:	-10 dBV/ 1M ohms
FX-RETURN:	-10dBV/ 47 k ohms
FX-SEND:	0 dBV/ 2.2 k ohms
REC.OUT:	0 dBV/ 800 ohms

POWERAMP SECTION:

'CURRENT FEEDBACK' solid state power amp


Output Power:	80	W rms into 8 ohms
	100		W rms into 4 ohms
PHONES:	0,5		W, 600 ohms
Frequency response:	20	Hz - 40 kHz (into 4 ohms)

Speakers:

CELESTION RockDriver Vintage, 12“, 8 ohms

GENERAL FEATURES:

Voltage:

230 V~ (European model)

117 V~ (North American model)

100 V~ (Japanese model)

Max. power consumption: 200 VA (into 4 ohms)

Mains Fuse:

slo-blo 1000 mA (230 V model) slo-blo 2000 mA (117 V model) slo-blo 2500 mA (100 V model)

Secondary Fuses:

2 x slo-blo 2500 mA (power amp)

Dimensions:

556 x 480 x 280 mm (W x H x D) 22“ x 19“ x 11“ (approx.)

Weight:

approx. 38 Lbs./ 17 kg

10

Image 10

Contents Attax Before CONNECTING, Read Instructions Important Safety InstructionsWichtige Sicherheitshinweise Important Advice on Safety Conseils DE Securite ImportantsImportanti Avvertimenti DI Sicurezza AvvertimentiAttax Channels Jacks and Control Features CleanSelecting Channels Standard SETUP/ Cable Connections Operating the AttaxAttax 80 and Signal Processors Recording OutputService and Preventive Maintenance TroubleshootingTechnical Data PhonesViel Erfolg und Spaß am tone mit Deinem Attax Lead 1 & Lead CleanHall Anschlüsse UND Bedienelemente Bei Röhrenamps üblich und erwünscht gegenseitig eineDER Attax 80 MIT Effektgeräten Standard SET UP / Verkabelung Bedienung DES AttaxDAS Anwählen DER Kanäle DER Recording Output DES AttaxWartung UND Service Mögliche FEHLERQUELLEN/ TroubleshootingTechnische Daten Avant LA Mise EN Fonction LES Canaux DE L’ATTAX Raccords ET Elements DE Commande Input prise de connexion pour Des guitares avec HumbuckerL’ATTAX 80 ET LES Processeurs D’EFFETS Standard SETUP/CABLAGE Maniement DE L’ATTAXSélection DES Canaux LA Sortie Enregistrement DE L’ATTAXEntretien ET Service Depistage DES PannesCaracteristiques Techniques Caracteristiques GeneralesPrima DI Utilizzare LO Strumento Canali ReverbCaratteristiche DEI Jack E DEI Controlli ItalianoSelezionare I Canali Lattax 80 E I Processori DI SegnaleSoluzione DEI Problemi Assistenza E Manutenzione PreventivaCaratteristiche Tecniche Sezione FinaleHughes & Kettner Antes DE LA Puesta EN MarchaLOS Canales DEL Attax Footswitch Conector para un pedal conmutador usual por Acometidas Y Elementos DE ManejoEL Attax 80 Y LOS Procesadores DE Efectos LA Seleccion DE LOS CanalesLA Salida Recording DEL Attax Deteccion Y Supresion DE ERRORES/TROUBLESHOOTING Mantenimiento Y ServicioDatos Tecnicos Datos GeneralesStamer Musikanlagen GmbH Magdeburger Str 66606 St.Wendel Andorra Korea