Hughes & Kettner Attax 80 manual Jacks and Control Features, Clean

ATTAX-MANUAL

2.0 JACKS AND CONTROL FEATURES

CLEAN EQ SECTION: BASS, MID and TREBLE controls for
the CLEAN channel. MID and TREBLE controls influence
each other, as is standard in tube amps: if you boost the
treble, the mids are cut and vice versa. This sound-shaping
		LEAD EQ SECTION: Active BASS, passive MID and
feature allows you to dial in a wide variety of subtle tonal		TREBLE tone controls for the LEAD channel. Here
variations.		too, MID and TREBLE influence each other for the
				MAINS: AC power
		widest possible range of subtle tonal variations.		switch.
CLEAN VOL: Determines
the CLEAN channel's volu-
me. Depending on the type
	LEAD GAIN: Controls the		MODE 2: Selects either the LEAD 1 or LEAD 2
of pickups in your instru-
	amount of distortion in		modes. LEAD 2 is active when the button is
ment, the amp will begin to
	the LEAD channel.		pressed.
clip somewhere around the
12 o'clock setting
(SoftClick).

				CLEAN									LEAD							MASTER
		5		0		0	0	CHANNEL		5		0		0		0	MODE 2	5		5	5
								SELECT
	0	10	-5	+5	-5	+5	-5	+5	0	10	-5	+5	-5	+5	-5	+5	0	10	0	10	0	10
INPUT	CLEAN VOL		BASS			MID	TREBLE		LEAD GAIN		BASS			MID	TREBLE		LEAD MASTER		REVERB		MASTER		MAINS

INPUT: The input jack sensitivity
is broad enough to handle
					MASTER: Controls the amp's master volume
guitars equipped with hum-
					level. The signal level of the RECORDING
buckers, active pickups, or
		LEAD MASTER: Determines the LEAD			OUT jack is unaffected by the MASTER
single coils.
		channel volume level in relation to the			control.
		CLEAN channel volume level.
CHANNEL SELECT: This channel selector
				REVERB: Controls how much integrated reverb is
switch activates either the CLEAN or LEAD
				added to the signal. Reverb is automatically
channel. The LEAD channel is active when	RED LEAD LED: The red LED illuminates when
				adjusted for each channel when you switch
the button is pressed.	the LEAD channel is active.
				channels.
MAINS: Connect the included Euro-norm		HEADPHONES: 1/4" head-
mains cord to this socket. Ensure the amp's
		phones jack. The speaker
voltage rating matches your local AC			FOOTSWITCH: Jack for a standard footswitch (e.g. Hughes &
		is automatically switched
voltage rating before you plug the cord into		off when a plug is inserted	Kettner FS-1); allows you to switch back and forth between the
the wall socket.		into this jack.	CLEAN and LEAD channels. When using a footswitch, ensure the

CHANNEL SELECT switch on the ATTAX 80's front panel is set to

CLEAN.

	CAUTION!
	TO PREVENT THE RISK OF FIRE AND
	SHOCK HAZARD DON´T EXPOSE THIS
	APPLIANCE TO MOISTURE OR RAIN.
	DO NOT OPEN CASE; NO USER
	SERVICEABLE PARTS INSIDE. REFER
	SERVICING TO QUALIFIED SERVICE
	PERSONNEL.	LEAVE ENOUGH SPACE FOR PROPER VENTILATION!		MADE IN ST. WENDEL GERMANY
	230 V~	HEAD	OUTPUT 100 WATTS	REC	FX-LOOP		FOOT
	100 V~	PHONES	MIN. IMP. 4 Ohms	OUT	RETURN	SEND	SWITCH
50 - 60 Hz
Max. power	117 V~
consumption							Ser. No.
240 VA

	RECORDING OUT: Feeds a mixing
			SEND: Connect your
	console, DI box or additional power
SPEAKERS: 1/4" jacks for external speakers. The two jacks are connected in par-			processor's INPUT to
	amp and speaker cabinet.
allel. When using these outputs, ensure the overall combined impedance of the			this jack.
connected speakers is not lower than 4 ohms! For the ATTAX 80 combo
version, you can connect one additional 60-watt cabinet in parallel to the
internal speaker. Make sure this cabinet has minimum rating of 8 ohms.		RETURN: Connect this jack to your
		effects processor's OUTPUT jack.

ENGLISH

7