Pioneer VSX-D514, VSX-D714 manual Additional information Chapter, Troubleshooting

Page 70

10Additional information

Chapter 10:

Additional information

Troubleshooting

Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.

Problem	Remedy
The power does not turn on.	• Connect the power plug to the wall outlet.
	• Disconnect the power plug from the outlet, and insert again.
	• Make sure there are no loose strands of speaker wire touching the
	rear panel. This could cause the receiver to shut off automatically.
	• If the power shuts off automatically, take the unit to your nearest
	Pioneer authorized service center or your dealer for servicing.
	• The unit may have been switched on using the wrong voltage
	setting. Make sure you switch the VOLTAGE SELECTOR on the rear
	panel to the right voltage for your country or region, then reset the
	unit (page 72) before switching on again.

No sound is output when a • Make sure the component is connected correctly (refer to
function is selected.	Connecting up on page 14).
	• Press MUTE on the remote control to turn muting off.
	• Adjust the MASTER VOLUME.

No image is output when a • Make sure the component is connected correctly (refer to
function is selected.	Connecting up on page 14).
	• Select the correct component (use the MULTI CONTROL buttons).

70

En

Image 70

Contents VSX-D514VSX-D714VSX-D814 Voltage selector Risk of Electric Shock Do not OpenEnglish Italiano Français Deutsch Nederlands EspañolControlling the rest of your system Using the tunerMaking recordings Additional informationEnglish Italiano Français Before you startDeutsch Nederlands Español Before you start Operating range of remote control unit Introduction to home theater Minute guideMinute guide Chapter English Italiano Français Deutsch Nederlands EspañolHook up your DVD player 02 5 minute guide Listening to Surround SoundHook up your TV Español VSX-D714 Powered subwooferMinute guide Connect your speakers02 5 minute guide VSX-D814 Passive Powered subwooferBack Play a DVD, and adjust the volume to your liking VSX-D8140ch 3.0ch 0ch*4.0ch 0ch 5.0ch 02 5 minute guide Using the Quick Setup1ch 3.1ch 1ch*4.1ch 1ch 5.1ch 1ch 0chFWD MID Back Press Enter Use the Multi JOG dial to choose your room sizeConnecting up This receiver Satellite tuner CD player Connecting up Connecting digital componentsCD recorder DVD playerConnecting up Connecting audio components This receiverConnecting up Connecting DVD 5.1 channel components Italiano FrançaisConnecting up Connecting video components Connecting to the front panel video terminalFM wire antenna Connecting up Connecting antennasUsing external antennas DeutschConnecting up Connecting the speakers VSX-D514/D714 Connecting up Connecting the speakers VSX-D814 English Italiano Français DeutschSpeaker terminals Connecting upHints on speaker placement B speaker systemsSpeaker placement diagrams Overhead view of speaker setupConnecting up Connecting additional amplifiers VSX-D714Power cord caution ComponentsIllustration shows the VSX-D814, but Front panel VSX-D514 Controls and displaysControls and displays Chapter Italiano FrançaisControls and displays English Italiano STANDBY/ON Master VolumeControls and displays Front panel VSX-D714/D814 Français Deutsch NederlandsVideo Input SB CH ModeSpeakers BandControls and displays Display Remote control CH Select Master Volume +Mcacc Setup Level +Return AccessSubtitle Band DTV ON/OFFVolume + TV Control Input SelectListening to your system Chapter Listening to your systemWhile listening to a source, press Using the Advanced surround effects Listening to your systemPanel to select the input signal corre Choosing the input signalPress Signal Select on the front Listening to your system Listening in stereoDTS-ES/Dolby Digital Matrix encoded VSB on VSB OFF Press Tone to select the frequency you want to adjust Listening to your system Using Midnight and LoudnessListening VSX-D514 model Press DVD/LD on the remote control or the front panelSelecting the multichannel analog inputs Start playback of the component you selected in stepOff Listening to your system Using the sleep timer90 min Press Receiver Press Sleep repeatedly to set the sleep timeSetting up the receiver Chapter Setting up the receiverChoosing your receiver setup Surround back speaker distance setting Setting up the receiverSurround right speaker distance setting Surround left speaker distance settingFS-CS-SS FL-C -S Speaker settingSurround back speaker setting FL-C -SS FS-C -SS FL-C -SLLFE attenuator setting Subwoofer settingCrossover frequency setting 10 dBFront right speaker distance setting Front speaker distance settingFront left speaker distance setting Center speaker distance settingSurround back speaker distance setting Surround right speaker distance settingSurround left speaker distance setting Subwoofer distance settingComponent video input settings Dynamic range control settingDual mono setting Digital input settingsSR+ control for Pioneer plasma displays Press Receiver Press Mcacc Setup Function setting for Video inputManually calibrating your listening area Mcacc Setting separate channel levels for listening modes R RSUse Level +/- to adjust the speaker levels in turn Using the SR+ mode with a Pioneer plasma displayWhen you’re done, press Test Tone to turn off the test tone English Italiano Français Deutsch Nederlands Español Tuning directly to a station Using the tunerUsing the tuner Chapter Listening to the radioTune to a station you want to memorize Using the tunerSaving station presets Press T.EDIT Tuner EditListening to station presets Naming station presetsChanging the frequency step Making recordings Chapter Making recordingsMaking an audio or a video recording Controlling the rest of your system Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your system ChapterWhen you’re done, press Receiver Programming signals from other remote controlsUse the number buttons to enter the preset code Controlling the rest of your systemWhen you’re done, press Receiver to store the operations Erasing all of your programmed settingsClearing all the remote control settings Direct functionInput VolumeControlling the rest of your system Controls for TVs Select ChannelControls for other components DiscCD/MD/CD-R/VCR/LD Enter GuideManufacturer Code On digital STBDVD Recorder ManufacturerCodeKenwood Sharp Samsung STB Additional information TroubleshootingAdditional information Chapter Set the Signal Select to AUTO, Digital or Analog Additional informationResetting the main unit Switching the speaker impedanceAudio section Additional information SpecificationsAmplifier section Video SectionAM Tuner Section Cleaning the unitFM Tuner Section MiscellaneousPioneer Corporation