Pioneer VSX-D714 manual Additional information, Set the Signal Select to AUTO, Digital or Analog

Page 71

Additional information

10

Problem

Remedy

Considerable noise in radio

• Tune in the correct frequency.

broadcasts.

• Connect the antenna (refer to page 19).

 

• Route any loose cables away from the antenna terminals and

 

wires.

 

• Fully extend the FM wire antenna, position for best reception, and

 

secure to a wall.

 

• Connect an outdoor FM antenna (refer to page 19).

 

• Adjust the direction and position for best reception.

 

• Connect an additional internal or external AM antenna (refer to

 

page 19).

 

• Turn off the equipment causing the noise or move it away from the

 

receiver.

 

• Move antennas farther away from equipment causing the noise.

 

 

Broadcast stations cannot be

• Connect an outdoor antenna (refer to page 19).

selected automatically.

 

 

 

No sound from surround or

• Refer to Speaker setting on page 46 to check the speaker settings.

center speakers.

• VSX-D714/D814 only – Refer to Manually calibrating your listening

 

area (MCACC) on page 52 to check the speaker levels.

 

• Connect the speakers properly (refer to page 20).

English Italiano Français

No sound from surround back speakers (VSX-D714/ D814 only).

•Refer to Surround back speaker setting on page 46 to check the surround back speaker settings.

•Refer to Manually calibrating your listening area (MCACC) on page 52 to check the speaker levels.

•Refer to Using the Surround Back Channel (SB CH) on page 39 to make sure the SB CH MODE and the sound mode are set for surround back sound.

Deutsch

No sound from subwoofer.

• Make sure the subwoofer is switched on.

 

• If the subwoofer has a volume knob, make sure it’s turned up.

 

• Switch the Subwoofer setting on page 47 to YES or PLUS.

 

• Switch the LFE attenuator setting on page 47 to 0 dB or 10 dB.

 

• The Dolby Digital or DTS source you are listening to does not have

 

an LFE channel.

 

 

Noise during playback of a

• Move the cassette deck further from your receiver, until the noise

cassette deck.

disappears.

 

 

Sound is produced from

• Set the SIGNAL SELECT to AUTO, DIGITAL or ANALOG

other components, but not

according to the type of connections made. (refer to page 38).

from LD or DVD player.

• Set the digital input settings correctly (refer to page 50).

 

• Make digital connections (refer to page 15) and set the SIGNAL

 

SELECT to DIGITAL (refer to page 38).

 

• Refer to the instruction manual supplied with the DVD player.

 

 

Nederlands Español

71

En

Page 70 Page 72
Image 71
Page 70 Page 72
Contents VSX-D514VSX-D714VSX-D814 Risk of Electric Shock Do not Open Voltage selectorItaliano Français Deutsch Nederlands Español EnglishAdditional information Using the tunerMaking recordings Controlling the rest of your systemDeutsch Nederlands Español Before you startEnglish Italiano Français Before you start Operating range of remote control unit English Italiano Français Deutsch Nederlands Español Minute guideMinute guide Chapter Introduction to home theaterHook up your TV 02 5 minute guide Listening to Surround SoundHook up your DVD player Connect your speakers VSX-D714 Powered subwooferMinute guide EspañolBack VSX-D814 Passive Powered subwoofer02 5 minute guide VSX-D814 Play a DVD, and adjust the volume to your liking1ch 0ch 02 5 minute guide Using the Quick Setup1ch 3.1ch 1ch*4.1ch 1ch 5.1ch 0ch 3.0ch 0ch*4.0ch 0ch 5.0chPress Enter Use the Multi JOG dial to choose your room size FWD MID BackConnecting up DVD player Connecting up Connecting digital componentsCD recorder This receiver Satellite tuner CD playerThis receiver Connecting up Connecting audio componentsItaliano Français Connecting up Connecting DVD 5.1 channel componentsConnecting to the front panel video terminal Connecting up Connecting video componentsDeutsch Connecting up Connecting antennasUsing external antennas FM wire antennaConnecting up Connecting the speakers VSX-D514/D714 English Italiano Français Deutsch Connecting up Connecting the speakers VSX-D814B speaker systems Connecting upHints on speaker placement Speaker terminalsOverhead view of speaker setup Speaker placement diagramsVSX-D714 Connecting up Connecting additional amplifiersComponents Power cord cautionIllustration shows the VSX-D814, but Italiano Français Controls and displaysControls and displays Chapter Front panel VSX-D514Controls and displays Français Deutsch Nederlands STANDBY/ON Master VolumeControls and displays Front panel VSX-D714/D814 English ItalianoBand SB CH ModeSpeakers Video InputControls and displays Display Remote control Level + Master Volume +Mcacc Setup CH SelectBand DTV ON/OFF AccessSubtitle ReturnTV Control Input Select Volume +While listening to a source, press Listening to your systemListening to your system Chapter Listening to your system Using the Advanced surround effectsListening to your system Listening in stereo Choosing the input signalPress Signal Select on the front Panel to select the input signal correDTS-ES/Dolby Digital Matrix encoded VSB on VSB OFF Listening Listening to your system Using Midnight and LoudnessPress Tone to select the frequency you want to adjust Start playback of the component you selected in step Press DVD/LD on the remote control or the front panelSelecting the multichannel analog inputs VSX-D514 modelPress Receiver Press Sleep repeatedly to set the sleep time Listening to your system Using the sleep timer90 min OffChoosing your receiver setup Setting up the receiverSetting up the receiver Chapter Surround left speaker distance setting Setting up the receiverSurround right speaker distance setting Surround back speaker distance settingFL-C -SS FS-C -SS FL-C -SL Speaker settingSurround back speaker setting FS-CS-SS FL-C -S10 dB Subwoofer settingCrossover frequency setting LFE attenuator settingCenter speaker distance setting Front speaker distance settingFront left speaker distance setting Front right speaker distance settingSubwoofer distance setting Surround right speaker distance settingSurround left speaker distance setting Surround back speaker distance settingDigital input settings Dynamic range control settingDual mono setting Component video input settingsSR+ control for Pioneer plasma displays Manually calibrating your listening area Mcacc Function setting for Video inputPress Receiver Press Mcacc Setup R RS Setting separate channel levels for listening modesWhen you’re done, press Test Tone to turn off the test tone Using the SR+ mode with a Pioneer plasma displayUse Level +/- to adjust the speaker levels in turn English Italiano Français Deutsch Nederlands Español Listening to the radio Using the tunerUsing the tuner Chapter Tuning directly to a stationPress T.EDIT Tuner Edit Using the tunerSaving station presets Tune to a station you want to memorizeChanging the frequency step Naming station presetsListening to station presets Making an audio or a video recording Making recordingsMaking recordings Chapter Controlling the rest of your system Chapter Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your systemControlling the rest of your system Programming signals from other remote controlsUse the number buttons to enter the preset code When you’re done, press ReceiverDirect function Erasing all of your programmed settingsClearing all the remote control settings When you’re done, press Receiver to store the operationsSelect Channel VolumeControlling the rest of your system Controls for TVs InputDisc Controls for other componentsEnter Guide CD/MD/CD-R/VCR/LDManufacturerCode On digital STBDVD Recorder Manufacturer CodeKenwood Sharp Samsung STB Additional information Chapter TroubleshootingAdditional information Additional information Set the Signal Select to AUTO, Digital or AnalogSwitching the speaker impedance Resetting the main unitVideo Section Additional information SpecificationsAmplifier section Audio sectionMiscellaneous Cleaning the unitFM Tuner Section AM Tuner SectionPioneer Corporation
Top Page Image Contents