Pioneer Guide to Connecting and Setting Up Your Stereo Receiver for Best Performance

Page 23

Connecting up

03

Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen.

If possible, place the surround speakers slightly above ear level.

Try not to place the surround speakers further away from the listening position than the front and center speakers. Doing so can weaken the surround sound effect.

To achieve the best possible surround sound, install your speakers as shown below. Be sure all speakers are installed securely to prevent accidents and improve sound quality.

If you choose to install the center speaker on top of the TV, be sure to secure it with putty, or by other suitable means, to reduce the risk of damage or injury resulting from the speaker falling from the TV in the event of external shocks such as earthquakes.

Make sure no exposed speaker wire is touching the rear panel, this may cause the receiver to turn off automatically.

Speaker placement diagrams

The following illustrations show 6.1 and 7.1 channel speaker setups.

Overhead view of speaker setup

Front

 

Front

Left

Center

Right

 

 

Subwoofer

Surround

 

Surround

Left

 

Right

 

Listening Position

Surround Back Left

Surround Back Right

Single Surround Back Speaker

3-D view of 6.1 channel speaker setup

3-D view of 7.1 channel speaker setup

English Italiano Français Deutsch Nederlands

VSX-D514 only – Follow the speaker placement diagrams below, disregarding the surround back speakers.

VSX-D714 only – See Connecting additional amplifiers on page 24 for more on connecting a surround back speaker.

Español

23

En

Image 23
Contents VSX-D514VSX-D714VSX-D814 Risk of Electric Shock Do not Open Voltage selectorItaliano Français Deutsch Nederlands Español EnglishAdditional information Using the tunerMaking recordings Controlling the rest of your systemDeutsch Nederlands Español Before you startEnglish Italiano Français Before you start Operating range of remote control unit English Italiano Français Deutsch Nederlands Español Minute guideMinute guide Chapter Introduction to home theaterHook up your TV 02 5 minute guide Listening to Surround SoundHook up your DVD player Connect your speakers VSX-D714 Powered subwooferMinute guide EspañolBack VSX-D814 Passive Powered subwoofer02 5 minute guide VSX-D814 Play a DVD, and adjust the volume to your liking1ch 0ch 02 5 minute guide Using the Quick Setup1ch 3.1ch 1ch*4.1ch 1ch 5.1ch 0ch 3.0ch 0ch*4.0ch 0ch 5.0chPress Enter Use the Multi JOG dial to choose your room size FWD MID BackConnecting up DVD player Connecting up Connecting digital componentsCD recorder This receiver Satellite tuner CD playerThis receiver Connecting up Connecting audio componentsItaliano Français Connecting up Connecting DVD 5.1 channel componentsConnecting to the front panel video terminal Connecting up Connecting video componentsDeutsch Connecting up Connecting antennasUsing external antennas FM wire antennaConnecting up Connecting the speakers VSX-D514/D714 English Italiano Français Deutsch Connecting up Connecting the speakers VSX-D814B speaker systems Connecting upHints on speaker placement Speaker terminalsOverhead view of speaker setup Speaker placement diagramsVSX-D714 Connecting up Connecting additional amplifiersComponents Power cord cautionIllustration shows the VSX-D814, but Italiano Français Controls and displaysControls and displays Chapter Front panel VSX-D514Controls and displays Français Deutsch Nederlands STANDBY/ON Master VolumeControls and displays Front panel VSX-D714/D814 English ItalianoBand SB CH ModeSpeakers Video InputControls and displays Display Remote control Level + Master Volume +Mcacc Setup CH SelectBand DTV ON/OFF AccessSubtitle ReturnTV Control Input Select Volume +While listening to a source, press Listening to your systemListening to your system Chapter Listening to your system Using the Advanced surround effectsListening to your system Listening in stereo Choosing the input signalPress Signal Select on the front Panel to select the input signal correDTS-ES/Dolby Digital Matrix encoded VSB on VSB OFF Listening Listening to your system Using Midnight and LoudnessPress Tone to select the frequency you want to adjust Start playback of the component you selected in step Press DVD/LD on the remote control or the front panelSelecting the multichannel analog inputs VSX-D514 modelPress Receiver Press Sleep repeatedly to set the sleep time Listening to your system Using the sleep timer90 min OffChoosing your receiver setup Setting up the receiverSetting up the receiver Chapter Surround left speaker distance setting Setting up the receiverSurround right speaker distance setting Surround back speaker distance settingFL-C -SS FS-C -SS FL-C -SL Speaker settingSurround back speaker setting FS-CS-SS FL-C -S10 dB Subwoofer settingCrossover frequency setting LFE attenuator settingCenter speaker distance setting Front speaker distance settingFront left speaker distance setting Front right speaker distance settingSubwoofer distance setting Surround right speaker distance settingSurround left speaker distance setting Surround back speaker distance settingDigital input settings Dynamic range control settingDual mono setting Component video input settingsSR+ control for Pioneer plasma displays Manually calibrating your listening area Mcacc Function setting for Video inputPress Receiver Press Mcacc Setup R RS Setting separate channel levels for listening modesWhen you’re done, press Test Tone to turn off the test tone Using the SR+ mode with a Pioneer plasma displayUse Level +/- to adjust the speaker levels in turn English Italiano Français Deutsch Nederlands Español Listening to the radio Using the tunerUsing the tuner Chapter Tuning directly to a stationPress T.EDIT Tuner Edit Using the tunerSaving station presets Tune to a station you want to memorizeChanging the frequency step Naming station presetsListening to station presets Making an audio or a video recording Making recordingsMaking recordings Chapter Controlling the rest of your system Chapter Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your systemControlling the rest of your system Programming signals from other remote controlsUse the number buttons to enter the preset code When you’re done, press ReceiverDirect function Erasing all of your programmed settingsClearing all the remote control settings When you’re done, press Receiver to store the operationsSelect Channel VolumeControlling the rest of your system Controls for TVs InputDisc Controls for other componentsEnter Guide CD/MD/CD-R/VCR/LDManufacturerCode On digital STBDVD Recorder Manufacturer CodeKenwood Sharp Samsung STB Additional information Chapter TroubleshootingAdditional information Additional information Set the Signal Select to AUTO, Digital or AnalogSwitching the speaker impedance Resetting the main unitVideo Section Additional information SpecificationsAmplifier section Audio sectionMiscellaneous Cleaning the unitFM Tuner Section AM Tuner SectionPioneer Corporation