Pioneer How to Reset a Receiver to Factory Settings

Page 72

10Additional information

Problem			Remedy
No sound is output or a noise			• Set the digital volume level of the player to full, or to the neutral
is output when software with			position.
DTS is played back.

When a search is performed			• This is not a malfunction, but be sure to turn the volume down to
by a DTS compatible CD			prevent the output of loud noise from your speakers.
player during playback, noise
is output.

Can’t operate the remote			• Replace the batteries (refer to page 5).
control.			• Operate within 7 m, 30° of the remote sensor on the front panel
			(refer to page 6).
			• Remove the obstacle or operate from another position.
			• Avoid exposing the remote sensor on the front panel to direct light.

The display is dark or off.			• Press FL DIMMER on the remote control repeatedly to return to
			the default.

•If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions.

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.

1Switch the receiver on.

2While holding down the TONE button,

press and hold the STANDBY/ON button for about three seconds.

3When you see RESET? appear in the display, press the TONE button.

OK? shows in the display.

4Press TONE once more to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings.

Switching the speaker impedance

We recommend using speakers of 8Ω with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6Ω impedance rating.

•With the receiver in standby, press STANDBY/ON while holding down the SPEAKERS / SPEAKER IMPEDANCE button. Each time you do this, you switch between the impedance settings:

•SP 6 OHM – Use this setting if your speakers are rated at 6Ω.

•SP 8 OHM – Use this setting if your speakers are rated at 8Ω or more.

72

En

Image 72

Contents VSX-D514VSX-D714VSX-D814 Voltage selector Risk of Electric Shock Do not OpenEnglish Italiano Français Deutsch Nederlands EspañolUsing the tuner Making recordingsControlling the rest of your system Additional informationBefore you start English Italiano FrançaisDeutsch Nederlands Español Before you start Operating range of remote control unit Minute guide Minute guide ChapterIntroduction to home theater English Italiano Français Deutsch Nederlands Español02 5 minute guide Listening to Surround Sound Hook up your DVD playerHook up your TV VSX-D714 Powered subwoofer Minute guideEspañol Connect your speakersVSX-D814 Passive Powered subwoofer 02 5 minute guideBack Play a DVD, and adjust the volume to your liking VSX-D81402 5 minute guide Using the Quick Setup 1ch 3.1ch 1ch*4.1ch 1ch 5.1ch0ch 3.0ch 0ch*4.0ch 0ch 5.0ch 1ch 0chFWD MID Back Press Enter Use the Multi JOG dial to choose your room sizeConnecting up Connecting up Connecting digital components CD recorderThis receiver Satellite tuner CD player DVD playerConnecting up Connecting audio components This receiverConnecting up Connecting DVD 5.1 channel components Italiano FrançaisConnecting up Connecting video components Connecting to the front panel video terminalConnecting up Connecting antennas Using external antennasFM wire antenna DeutschConnecting up Connecting the speakers VSX-D514/D714 Connecting up Connecting the speakers VSX-D814 English Italiano Français DeutschConnecting up Hints on speaker placementSpeaker terminals B speaker systemsSpeaker placement diagrams Overhead view of speaker setupConnecting up Connecting additional amplifiers VSX-D714Power cord caution ComponentsIllustration shows the VSX-D814, but Controls and displays Controls and displays ChapterFront panel VSX-D514 Italiano FrançaisControls and displays STANDBY/ON Master Volume Controls and displays Front panel VSX-D714/D814English Italiano Français Deutsch NederlandsSB CH Mode SpeakersVideo Input BandControls and displays Display Remote control Master Volume + Mcacc SetupCH Select Level +Access SubtitleReturn Band DTV ON/OFFVolume + TV Control Input SelectListening to your system Listening to your system ChapterWhile listening to a source, press Using the Advanced surround effects Listening to your systemChoosing the input signal Press Signal Select on the frontPanel to select the input signal corre Listening to your system Listening in stereoDTS-ES/Dolby Digital Matrix encoded VSB on VSB OFF Listening to your system Using Midnight and Loudness Press Tone to select the frequency you want to adjustListening Press DVD/LD on the remote control or the front panel Selecting the multichannel analog inputsVSX-D514 model Start playback of the component you selected in stepListening to your system Using the sleep timer 90 minOff Press Receiver Press Sleep repeatedly to set the sleep timeSetting up the receiver Setting up the receiver ChapterChoosing your receiver setup Setting up the receiver Surround right speaker distance settingSurround back speaker distance setting Surround left speaker distance settingSpeaker setting Surround back speaker settingFS-CS-SS FL-C -S FL-C -SS FS-C -SS FL-C -SLSubwoofer setting Crossover frequency settingLFE attenuator setting 10 dBFront speaker distance setting Front left speaker distance settingFront right speaker distance setting Center speaker distance settingSurround right speaker distance setting Surround left speaker distance settingSurround back speaker distance setting Subwoofer distance settingDynamic range control setting Dual mono settingComponent video input settings Digital input settingsSR+ control for Pioneer plasma displays Function setting for Video input Press Receiver Press Mcacc SetupManually calibrating your listening area Mcacc Setting separate channel levels for listening modes R RSUsing the SR+ mode with a Pioneer plasma display Use Level +/- to adjust the speaker levels in turnWhen you’re done, press Test Tone to turn off the test tone English Italiano Français Deutsch Nederlands Español Using the tuner Using the tuner ChapterTuning directly to a station Listening to the radioUsing the tuner Saving station presetsTune to a station you want to memorize Press T.EDIT Tuner EditNaming station presets Listening to station presetsChanging the frequency step Making recordings Making recordings ChapterMaking an audio or a video recording Setting the remote to control other components Selecting preset codes directlyControlling the rest of your system Controlling the rest of your system ChapterProgramming signals from other remote controls Use the number buttons to enter the preset codeWhen you’re done, press Receiver Controlling the rest of your systemErasing all of your programmed settings Clearing all the remote control settingsWhen you’re done, press Receiver to store the operations Direct functionVolume Controlling the rest of your system Controls for TVsInput Select ChannelControls for other components DiscCD/MD/CD-R/VCR/LD Enter GuideOn digital STB DVD RecorderManufacturer Code ManufacturerCodeKenwood Sharp Samsung STB Troubleshooting Additional informationAdditional information Chapter Set the Signal Select to AUTO, Digital or Analog Additional informationResetting the main unit Switching the speaker impedanceAdditional information Specifications Amplifier sectionAudio section Video SectionCleaning the unit FM Tuner SectionAM Tuner Section MiscellaneousPioneer Corporation