Yamaha HTY-750 owner manual 69 En

Page 71

Adjusting the audio balance

3Press / to adjust the channel volume.

ENTER

Control range: –10.0 dB to +10.0 dB

4Wait for a few seconds without operating this unit when you have completed your adjustment.

Notes

All channel levels cannot be adjusted when the stereo playback (see page 50), or My Surround (see page 45) is selected as the beam mode.

“FRONT L/R” cannot be adjusted when Stereo plus 3 Beam is selected as the beam mode (see page 41).

Only CENTER can be adjusted when My Beam is selected as the beam mode (see page 51).

“FRONT L/R” are automatically adjusted depending on the settings of the other channels when Stereo plus 3 Beam or stereo playback is selected as the beam mode (see pages 45 and 50).

y

If the level of a particular channel cannot be adjusted, “– –dB” appears in the front panel display.

OPERATION

ADVANCED

 

 

English

69 En

Image 71
Contents HTY-750 For U.K. Customers Contents Overview Features Features Using this manual Cable clamp ⋅1 Supplied accessoriesRemote control ⋅1 STANDBY/ON Controls and functionsFront panel InputFront panel display Rear panel 10 En Remote control11 En Numeric buttons 12 En13 En InstallationBefore installing this unit Installing this unitExample Installation examples14 En This unit Using a rack15 En For video output Connections16 En For audio input For audio outputAffixing cables 17 EnCables used for connections Audio OSD video pin cable Audio pin cable Optical cable Connecting a TV18 En AudioAudio pin cable Digital audio pin cable Connecting a DVD player/recorderVideo signal to the TV 19 EnDigital satellite tuner Or cable TV tuner Connecting a digital satellite tuner or a cable TV tuner20 En Audio pin cable Optical cableDigital airwave tuner Connecting a digital airwave tuner21 En Connect to the analog audio output jacks on the TV22 En Connecting a VCROptical Digital output Connecting other external components23 En 24 En Connecting a subwooferMonaural System input connector Subwoofer To the AC wall outlet Connecting the AC power supply cable25 En Getting started Installing batteries in the remote controlOperation range of the remote control Close the battery cover27 En Press STANDBY/ON again to set this unit to the standby modePress STANDBY/ON to turn on the power of this unit 28 En Using SET MenuDisplaying the OSD on-screen display 29 En Flow chart of SET Menu30 En Language SetupChanging OSD language SET MenuBeam optimization Sound optimization Auto Setup IntelliBeamFlow chart of Auto Setup 31 En32 En Installing the IntelliBeam microphonePress STANDBY/ON to turn off the power of this unit Center line Using Auto Setup IntelliBeam33 En Assembling the supplied cardboard Microphone stand34 En Auto SetupSet the operation mode selector to YSP Press / to select Auto Setup and press EnterBEAM+SOUND Optimz Auto Setup Start35 En Example Show Result36 En Check that the following screen is displayed on your TV37 En Error messages for Auto SetupBefore the Auto Setup procedure starts While the Auto Setup procedure is in progressMemory Using the system memorySaving settings 2MEMORY Save39 En Loading settingsMemory 2MEMORY SavePress / to select MEMORY1 1MEMORY Load40 En Press / to select Load and press Press Enter again41 En PlaybackSelecting the input source D V D X X X a U T O42 En Playing back sourcesC R A U X X X X a U T OMuting the sound Adjusting the volumeD I O X M U T E X O N 43 EnPress 5BEAM to select 5 Beam Enjoying surround soundBeam 44 En45 En Stereo plus 3 BeamMy Surround Source Decoder indicators46 En Surround modes and recommended sources47 En Enjoying 2-channel sourcesSurround sound Press TV Press Volume +/- to adjust the volume level48 En Select the TV channel you want to watch49 En Adjusting surround mode parametersWhen Dolby Pro Logic II Music is selected When DTS Neo6 Music is selected50 En Press Stereo to select the stereo playback as the beam modeEnjoying stereo sound T E R E O X M O D EPress and hold MY Beam for more than two seconds Using auto-adjust functionPlaying back sound clearly My Beam 51 En52 En Using manual-adjust functionG L E NIGHTCINEMA, NIGHTMUSIC, TV Equal 53 EnFlashes Lights up Using the sleep timerUnit to confirm the setting for the sleep timer 54 EnDisappears Canceling the sleep timerL E E P X X O F F 55 EnInput Menu 56 EnSound Menu Beam Menu57 En Manual SetupUsing Manual Setup 58 En Setting parametersInstalled Position Installed position of this unit 2BEAM MenuListening position from the unit Room width Beam Adjustment Beam adjustment59 En Horizontal Angle Horizontal angleFront left channel 60 EnBeam Travel Length Beam travel length Focal Length Focal lengthImage Location Image location Cimage Location61 En 62 En 1SOUND MenuAtone Control Cmute LevelTruBass Daudio DelayAudio Delay Audio delay 63 En64 En Ainput Mode3INPUT Menu Binput TrimPress / to select the desired character Cinput Rename65 En Input Rename Input rename Cunit SET 4DISPLAY Menu AF.DISPLAY SET Bosd SET67 En Adjusting the audio balanceUsing the test tone S T X L E F T68 En Using the audio output being played back69 En DTS Selecting the input mode70 En Auto71 En Adjusting the system parametersUsing the system parameters M O R Y X P R O T E C T72 En Press / to switch between Protect on and Protect OFFX X V O L U M E X S E T Setting the MAX VolumeSetting the Turn on Volume Press / to adjust the maximum volume levelM O X M O D E Setting the Demo ModePress / to adjust the initial volume level R N X O N X V O L U M E75 En Press / to switch between Demo on Demo OFF76 En Press / to switch between P.INPUT on P.INPUT OFFDisabling the front panel keys 77 En Setting the Factory PresetPress / to switch between F.PANEL on and F.PANEL OFF C T O R Y X P R E S E T78 En Press / to switch between Preset Reset and Preset CancelCode SET Remote control featuresSetting remote control codes 79 EnTV INPUT1/2 Controlling other components80 En Operating your TVOperation buttons for DVD players 81 EnOperating your DVD player/recorder Operating your STB CATV/Satellite tunerOperation buttons for VCR 82 EnOperating your VCR 83 En Using the TV macroSetting macros for the TV with the tuning capability Press Enter to confirm the macro settingOperating macros Setting macros for the TV without the tuning capabilityCanceling the macros 84 EnGeneral Troubleshooting85 En 86 En 87 En Remote control88 En GlossarySRS TruBass 89 EnLFE 0.1-channel PCM Linear PCMNumerics Index90 En 91 En SpecificationsConditions 92 EnCable TV Tuner List of remote control codesVCR DVD Player834 Satellite TunerTo your TV and DVD player Install this unit in the 4 Installation is completedItems used for connections and operations This guide Place this unit in front Connect this unit RackAbout the room environment About the IntelliBeam microphone