Yamaha HTY-750 owner manual 89 En, LFE 0.1-channel, PCM Linear PCM, SRS TruBass

Page 91

■LFE 0.1-channel

This channel is for the reproduction of low bass signals. The frequency range for this channel is 20 Hz to 120 Hz. This channel is counted as 0.1 because it only enforces a low-frequency range compared to the full-range reproduction by the other 5/6 channels in Dolby Digital or DTS 5.1/6.1-channel systems.

■PCM (Linear PCM)

Linear PCM is a signal format under which an analog audio signal is digitized, recorded, and transmitted without using any compression. This is used as a method of recording CDs and DVD audio. The PCM system uses a technique for sampling the size of the analog signal per very small unit of time. Standing for pulse code modulation, the analog signal is encoded as pulses and then modulated for recording.

■SRS TruBass

SRS TruBass is a psychoacoustic bass enhancement technology developed by SRS Labs, Inc. for speakers and headphone systems that delivers bass up to an octave below the physical capabilities of the speaker’s driver. SRS TruBass technology takes advantage of a spontaneous tendency of the human ears to infer low- range audio data when presented with higher-frequency harmonic signals. As a result, our ears can hear the original low-range sound that the speaker system is incapable of producing.

Glossary

INFORMATION	ADDITIONAL


English

89 En

Image 91

Contents HTY-750 For U.K. Customers Contents Overview Features Features Using this manual Remote control ⋅1 Supplied accessoriesCable clamp ⋅1 STANDBY/ON Controls and functionsFront panel InputFront panel display Rear panel 10 En Remote control11 En Numeric buttons 12 En13 En InstallationBefore installing this unit Installing this unit14 En Installation examplesExample 15 En Using a rackThis unit For video output Connections16 En For audio input For audio outputCables used for connections Audio 17 EnAffixing cables OSD video pin cable Audio pin cable Optical cable Connecting a TV18 En AudioAudio pin cable Digital audio pin cable Connecting a DVD player/recorderVideo signal to the TV 19 EnDigital satellite tuner Or cable TV tuner Connecting a digital satellite tuner or a cable TV tuner20 En Audio pin cable Optical cableDigital airwave tuner Connecting a digital airwave tuner21 En Connect to the analog audio output jacks on the TV22 En Connecting a VCR23 En Connecting other external componentsOptical Digital output Monaural System input connector Subwoofer Connecting a subwoofer24 En 25 En Connecting the AC power supply cableTo the AC wall outlet Getting started Installing batteries in the remote controlOperation range of the remote control Close the battery coverPress STANDBY/ON to turn on the power of this unit Press STANDBY/ON again to set this unit to the standby mode27 En Displaying the OSD on-screen display Using SET Menu28 En 29 En Flow chart of SET Menu30 En Language SetupChanging OSD language SET MenuBeam optimization Sound optimization Auto Setup IntelliBeamFlow chart of Auto Setup 31 EnPress STANDBY/ON to turn off the power of this unit Installing the IntelliBeam microphone32 En Center line Using Auto Setup IntelliBeam33 En Assembling the supplied cardboard Microphone stand34 En Auto SetupSet the operation mode selector to YSP Press / to select Auto Setup and press Enter35 En Auto Setup StartBEAM+SOUND Optimz Example Show Result36 En Check that the following screen is displayed on your TV37 En Error messages for Auto SetupBefore the Auto Setup procedure starts While the Auto Setup procedure is in progressMemory Using the system memorySaving settings 2MEMORY Save39 En Loading settingsMemory 2MEMORY SavePress / to select MEMORY1 1MEMORY Load40 En Press / to select Load and press Press Enter again41 En PlaybackSelecting the input source D V D X X X a U T O42 En Playing back sourcesC R A U X X X X a U T OMuting the sound Adjusting the volumeD I O X M U T E X O N 43 EnPress 5BEAM to select 5 Beam Enjoying surround soundBeam 44 EnMy Surround Stereo plus 3 Beam45 En Source Decoder indicators46 En Surround modes and recommended sourcesSurround sound Enjoying 2-channel sources47 En Press TV Press Volume +/- to adjust the volume level48 En Select the TV channel you want to watch49 En Adjusting surround mode parametersWhen Dolby Pro Logic II Music is selected When DTS Neo6 Music is selected50 En Press Stereo to select the stereo playback as the beam modeEnjoying stereo sound T E R E O X M O D EPress and hold MY Beam for more than two seconds Using auto-adjust functionPlaying back sound clearly My Beam 51 EnG L E Using manual-adjust function52 En NIGHTCINEMA, NIGHTMUSIC, TV Equal 53 EnFlashes Lights up Using the sleep timerUnit to confirm the setting for the sleep timer 54 EnDisappears Canceling the sleep timerL E E P X X O F F 55 EnInput Menu 56 EnSound Menu Beam MenuUsing Manual Setup Manual Setup57 En 58 En Setting parametersInstalled Position Installed position of this unit 2BEAM MenuListening position from the unit Room width Beam Adjustment Beam adjustment59 En Horizontal Angle Horizontal angleFront left channel 60 EnBeam Travel Length Beam travel length Focal Length Focal length61 En Cimage LocationImage Location Image location 62 En 1SOUND MenuAtone Control Cmute LevelTruBass Daudio DelayAudio Delay Audio delay 63 En64 En Ainput Mode3INPUT Menu Binput TrimPress / to select the desired character Cinput Rename65 En Input Rename Input renameCunit SET 4DISPLAY MenuAF.DISPLAY SET Bosd SET67 En Adjusting the audio balanceUsing the test tone S T X L E F T68 En Using the audio output being played back69 En DTS Selecting the input mode70 En Auto71 En Adjusting the system parametersUsing the system parameters M O R Y X P R O T E C T72 En Press / to switch between Protect on and Protect OFFX X V O L U M E X S E T Setting the MAX VolumeSetting the Turn on Volume Press / to adjust the maximum volume levelM O X M O D E Setting the Demo ModePress / to adjust the initial volume level R N X O N X V O L U M E75 En Press / to switch between Demo on Demo OFFDisabling the front panel keys Press / to switch between P.INPUT on P.INPUT OFF76 En 77 En Setting the Factory PresetPress / to switch between F.PANEL on and F.PANEL OFF C T O R Y X P R E S E T78 En Press / to switch between Preset Reset and Preset CancelCode SET Remote control featuresSetting remote control codes 79 EnTV INPUT1/2 Controlling other components80 En Operating your TVOperation buttons for DVD players 81 EnOperating your DVD player/recorder Operating your STB CATV/Satellite tunerOperating your VCR 82 EnOperation buttons for VCR 83 En Using the TV macroSetting macros for the TV with the tuning capability Press Enter to confirm the macro settingOperating macros Setting macros for the TV without the tuning capabilityCanceling the macros 84 En85 En TroubleshootingGeneral 86 En 87 En Remote control88 En GlossarySRS TruBass 89 EnLFE 0.1-channel PCM Linear PCM90 En IndexNumerics 91 En SpecificationsConditions 92 EnCable TV Tuner List of remote control codesVCR DVD Player834 Satellite TunerTo your TV and DVD player Install this unit in the 4 Installation is completedItems used for connections and operations This guide Place this unit in front Connect this unit RackAbout the room environment About the IntelliBeam microphone