Yamaha YDP-113 owner manual XG Native Parameter Change, XG Native Bulk Data reception only

7. SYSTEM EXCLUSIVE MESSAGES (XG Standard)

(1) XG Native Parameter Change

Data format: [F0H] -> [43H] -> [1nH] -> [4CH] -> [hhH] ->

	[mmH] -> [llH] -> [ddH] -> [F7H]
F0H =	Exclusive status
43H =	YAMAHA ID
1nH =	When received, n=0~F.
	When transmitted, n=0.
4CH = Model ID of XG
hhH =	Address High
mmH = Address Mid
llH =	Address Low
ddH =	Data
F7H =	End of Exclusive

Data size must match parameter size (2 or 4 bytes).

When the XG System On message is received, the MIDI sys- tem will be reset to its default settings.

The message requires approximately 50ms to execute, so sufficient time should be allowed before the next message is sent.

(2) XG Native Bulk Data (reception only)

Data format: [F0H] -> [43H] -> [0nH] -> [4CH] -> [aaH] ->

	[bbH] -> [hhH] -> [mmH] -> [llH] ->[ddH] ->...->
	[ccH] -> [F7H]
F0H =	Exclusive status
43H =	YAMAHA ID
0nH =	When received, n=0~F.
	When transmitted, n=0.
4CH = Model ID of XG
aaH =	ByteCount
bbH =	ByteCount
hhH =	Address High
mmH = Address Mid
llH =	Address Low
ddH =	Data
ccH =	Check sum
F7H =	End of Exclusive

•Receipt of the XG SYSTEM ON message causes reinitializa- tion of relevant parameters and Control Change values. Allow sufficient time for processing to execute (about 50 msec) before sending the YDP-113 another message.

•XG Native Parameter Change message may contain two or four bytes of parameter data (depending on the parameter size).

•For information about the Address and Byte Count values, refer to Table 1 below. Note that the table’s Total Size value gives the size of a bulk block. Only the top address of the block (00H, 00H, 00H) is valid as a bulk data address.

8.SYSTEM EXCLUSIVE MESSAGES (Digital Piano MIDI Format)

Data format: [F0H] -> [43H] -> [73H] -> [xxH] -> [nnH] -> [F7H]

F0H =	Exclusive status
43H =	Yamaha ID
73H =	Digital Piano ID
01H =	Product ID (YDP common)
or
7F=	Extended Product ID
xxH =	Product ID (YDP-113: 24H)
nnH =	Substatus
nn	Control
02H	Internal MIDI clock
03H	External MIDI clock
06H Bulk Data (the bulk data follows 06H)
F7H =	End of Exclusive

*When nn=02H or 03H, YDP common ID (01H) is rec- ognized as well as 75H.

9.SYSTEM EXCLUSIVE MESSAGES (Special Control)

Data format: [F0H] -> [43H] -> [73H] -> [66H] -> [11H] ->

	[0nH] -> [ccH] -> [vvH] -> [F7H]
F0H =	Exclusive status
43H =	Yamaha ID
73H =	Digital Piano ID
7FH =	Extended Product ID
xxH =	Product ID (YDP-113: 24H)
11H =	Special control
0nH =	Control MIDI change (n=channel number)
cc =	Control number
vv =	Value
F7H =	End of Exclusive

Control	Channel	ccH	vvH
Split Point	Always 00H	14H	14H : Split Key Number
Metronome	Always 00H	1BH	00H : off
			01H	: –
			02H	: 2/4
			03H	: 3/4
			04H	: 4/4
			05H	: 5/4
			06H	: 6/4
			7FH : No accent
Damper Level	ch: 00H-0FH	3DH(Sets the Damper Level
			for each channel)
			00H-7FH
Channel Detune ch: 00H-0FH		43H (Sets the Detune value
			for each channel)
			00H-7FH
Voice Reserve	ch: 00H-0FH	45H	00H	: Reserve off
			7FH : on*

*When Volume, Expression is received for Reserve On, they will be effective from the next Key On. Reserve Off is normal.

10.SYSTEM EXCLUSIVE MESSAGES (Others)

Data format: [F0H] -> [43H] -> [1nH] -> [27H] -> [30H] -> [00H]

-> [00H] -> [mmH] -> [llH] -> [ccH] -> [F7H]

Master Tuning (XG and last message priority) simultaneously changes the pitch of all channels.

F0H =	Exclusive Status
43H =	Yamaha ID
1nH =	When received, n=0~F.
	When transmitted, n=0.
27H =	Model ID of TG100
30H =	Sub ID
00H	=
00H	=
mmH = Master Tune MSB
llH =	Master Tune LSB
ccH =	don’t care (under 7FH)
F7H =	End of Exclusive

36 YDP-113Appendix/Anhang/Annexe/Apéndice