Crest Audio HPW Stereo input options, Both in the OUT position true stereo signal passes through

Page 22

stereo input - options 5

23gain 1&2 - These controls adjust the input gains of the two selectable inputs (TRS and RCA). Both Left and Right circuits are simultaneously adjusted. Unity gain is at the mid-point (with a detent), min and max gain adjust is 20dB. The stereo inputs were designed for line-level sources and can accommodate a wide range of input levels. Use the appropriate input when patching-in your external gear. For most semi-Pro or Pro outboard gear with balanced output jacks, use Stereo Line input 1. The TRS input jacks accept balanced or unbalanced sources. Use an adapter plug or cable to patch-in XLR gear. For semi-Pro or consumer equipment with RCA output jacks, use Stereo Line input 2.

24left, right and mono switchs - These buttons determine which signal(s) will be routed to the main buses, subgroup buses or post fader aux sends. The Pre-Fader Source (27) determines the source for the pre-fader aux sends.

both in the “OUT” position — true stereo signal passes through.

left button only in the “IN” position — only the left signal passes through. right button only in the “IN” position — only the right signal passes through. both in the “IN” position— a summed left and right mono signal passes through.

25line 2 switch - This button selects which inputs are active (Line 1 or Line 2 Inputs). By depressing this switch (“IN” position), line input 2 becomes active.

EQ features

Many audio signals coming into the console require some degree of corrective equaliza- tion in order to be part of a good sounding mix.

Each Stereo Input is equipped with a fixed-frequency, four-band EQ. The HF and LF bands have a shelving response. The HM band is bell-shaped, centered at 4kHz. The LM band is centered at 250Hz. The EQ circuitry is always in the signal path. Set all EQ controls to “0” (flat) if no equalization is desired.

26high frequency— HF 15dB boost and cut at 10kHz — Shelving Response high mid frequency— HM 15dB boost and cut centered at the 4kHz, Q of 1.5 low mid frequency— LF 15dB boost and cut centered at the 250Hz, Q of 1.5 low frequency— LF 15dB boost and cut at 80Hz — Shelving Response

23

24

25

26

p. 22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Hpwtm Mixing Console Page HPW Page Important Safety Instructions Sound Level dBA, Slow ResponseBewahren SIE Diese Sicherheitshinweise AUF Gardez CES Instructions Guarde Estas Instrucciones Page Table of contents Block diagram MuteMono Output +48VTALKBACK Mono input If the channel peak LED isEQ features Aux send featuresBus assign Mono Bus assignment featuresAux send level Left- RightChannel monitoring features Channel muting featuresChannel fader HPW Input Mono input optionsHPW Input EQ PCB lower Aux PRE option HPW Mono InputUser options Direct out D.O. option4features overview Rear panel featuresAutomix optional AutomixBoth in the OUT position true stereo signal passes through Stereo input optionsAffected by the Mute switch Stereo inputsSignal monitoring features Bus Assign5stereo input options HPW Input EQ PCB upperHPW Stereo Input SB7Rear panel connectors Features 6groups audio subgroupsGroup monitoring features GroupsFader-reverse function Using the HPW as a monitor console6groups Fader reverse w/LEDGroup mixing features Creating additional mixesGroup output 1/4TRS jack Group connectors- rear panelInsert jack 1/4TRS jack 50 PK/Sig LED AuxesAuxes auxiliary mixes 51 AFLAux output 1/4TRS and male XLR jacks Aux connectors-rear panel7auxes Insert jack 1/4TRS jackLeft and right main audio buses FeaturesLeft right 57 PK/Sig LED8left right Use the Fader63 100mm Fader Mono outputMono main audio bus 64 PK/Sig LEDLeft right, mono output Mono connectors- rear panelMain Mono output male XLR jack Matrix mix Matrix mixMatrix output 1/4TRS jack Gain Lo cut switch¡master section Stereo lo-cut filterAux 1/2 or 9/10 selector button Master section ¡Aux sends 1-2 or Bus Assign Mono Master sectionStereo fader Groups78 PK/Sig LED Alternate outputs features Limiter MasterGain reduction metering CompressorLow frequency- LF Ambience inputs featuresHigh frequency- HF BalanceMute 99 PRELevel Mute level¡ master section Master section monitoring and controlSource select switches Monitor meteringSolo operation Selected to avoid errorsMonitor output 1/4TRS jack rear panel Solo meteringPresets Mute scene edit/cancelSingle scene mode Headphone sourceLamp connectors Power supply monitorTalkback input Ext DC Connector Power supply internalOn-off switch Internal supplyPower supply External power supply front External power supply rearDC status Power supply controls frontPower supply controls rear AC input DC outputExternal Power Supply Power supply dual hookupPower supply dual Powering the HPW£ specifications +/- 18 volts @ 3 amps Main analog rails
Top Page Image Contents