Crest Audio HPW owner manual Important Safety Instructions, Sound Level dBA, Slow Response

Page 5

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using electrical products, basic cautions should always be followed, including the following:

1. Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with a dry cloth.

7.Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit from the apparatus.

11.Only use attachments/accessories provided by the manufacturer.

12.Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a

cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.Never break off the ground pin. Write for our free booklet “Shock Hazard and Grounding.” Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.

16.If this product is to be mounted in an equipment rack, rear support should be provided.

17.Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your plug‚ proceed as follows:

a)The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E‚ the earth symbol‚ colored green or colored green and yellow.

b)The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black.

c)The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red.

18.Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in suscep- tibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures:

Duration Per Day In Hours

Sound Level dBA, Slow Response

8

90

6

92

4

95

3

97

2

100

1 1⁄2

102

1

105

1⁄2

110

1⁄4 or less

115

According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Ear plugs or protectors to the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.

SAVE THESE INSTRUCTIONS!

Image 5
Contents Hpwtm Mixing Console Page HPW Page Sound Level dBA, Slow Response Important Safety InstructionsBewahren SIE Diese Sicherheitshinweise AUF Gardez CES Instructions Guarde Estas Instrucciones Page Table of contents Mute Block diagramMono Output +48VTALKBACK If the channel peak LED is Mono inputAux send features EQ featuresAux send level Bus assignment featuresBus assign Mono Left- RightChannel fader Channel muting featuresChannel monitoring features HPW Input EQ PCB lower Mono input optionsHPW Input User options HPW Mono InputAux PRE option Direct out D.O. optionRear panel features 4features overviewAutomix Automix optionalStereo input options Both in the OUT position true stereo signal passes throughStereo inputs Affected by the Mute switchBus Assign Signal monitoring featuresHPW Input EQ PCB upper 5stereo input optionsSB7 HPW Stereo InputRear panel connectors 6groups audio subgroups FeaturesGroups Group monitoring features6groups Using the HPW as a monitor consoleFader-reverse function Fader reverse w/LEDCreating additional mixes Group mixing featuresInsert jack 1/4TRS jack Group connectors- rear panelGroup output 1/4TRS jack Auxes auxiliary mixes Auxes50 PK/Sig LED 51 AFL7auxes Aux connectors-rear panelAux output 1/4TRS and male XLR jacks Insert jack 1/4TRS jackLeft right FeaturesLeft and right main audio buses 57 PK/Sig LEDUse the Fader 8left rightMono main audio bus Mono output63 100mm Fader 64 PK/Sig LEDMain Mono output male XLR jack Mono connectors- rear panelLeft right, mono output Matrix output 1/4TRS jack Matrix mixMatrix mix ¡master section Lo cut switchGain Stereo lo-cut filterAux sends 1-2 or Master section ¡Aux 1/2 or 9/10 selector button Stereo fader Master sectionBus Assign Mono Groups78 PK/Sig LED Alternate outputs features Gain reduction metering MasterLimiter CompressorHigh frequency- HF Ambience inputs featuresLow frequency- LF BalanceLevel 99 PREMute Mute levelMaster section monitoring and control ¡ master sectionMonitor metering Source select switchesMonitor output 1/4TRS jack rear panel Selected to avoid errorsSolo operation Solo meteringSingle scene mode Mute scene edit/cancelPresets Headphone sourceTalkback input Power supply monitorLamp connectors On-off switch Power supply internalExt DC Connector Internal supplyExternal power supply front External power supply rear Power supplyPower supply controls rear AC input Power supply controls frontDC status DC outputPower supply dual hookup External Power SupplyPowering the HPW Power supply dual+/- 18 volts @ 3 amps Main analog rails £ specifications