Crest Audio HPW Mono output, Mono main audio bus, 63 100mm Fader, 64 PK/Sig LED, 65 AFL

Page 37

mono output 9

mono (main audio bus)

features

The HPW is equipped with 3 main audio buses in addition to the 8 audio subgroups. This section of the manual deals with 1 of those 3 main buses - the Mono bus.The Mono bus is directly assignable from all of the Mono and Stereo Inputs, the 8 audio subgroups and the L-R main buses.

Since the Mono bus is directly-assignable from all input sources, and not a derived, summed L-R mix, a variety of uses are possible: Center-cluster feed in a L-C-R church install, subwoofer feed - assign only the appropriate, low-frequency sources to the bus, or use it to sum the L-R mixes to create a mono mix.

The Matrix Send pots allow the user to mix the post-fader/post-mute Mono sig- nal with the other 2 main outputs, plus the 8 groups. If the PRE button is pressed, the signal to the Matrix Send pots is pre-fader/pre-mute.This allows a totally independent output mix to be created. The main fader level will not affect the Matrix mix. The overall level of the entire Matrix mix is controlled by the Matrix Masters, located at the far right of the Master section.

See Matrix section for further matrix information

62Mute Switch w/LED

This switch will mute the post-fader output of the Mono audio bus.The LED will illu- minate when the mute is active. NOTE: These mute switches are NOT part of the programmable mute scenes.

63100mm Fader

This high-quality, 100mm fader is used to control the main output level. Any Post- fader feeds are affected by this control. Nominal position is at the “0” mark, with 10dB additional gain available above that point.

62

63

64

65

64PK/Sig LED

The FADER is equipped with a bicolor LED that displays the Pre-fader signal level with varying intensity green illumination, and also indicates impending audio overload (within 3dB of clipping) by turning red. Audio clipping is sensed both pre- and post- fader, so even if the fader is down, you will be informed of any bus-related overload problems.

65AFL

An AFL (After-Fader Listen) switch is provided that lets the operator monitor the audio signal in the console’s Solo system.When depressed, the Mono’s post-fader, post-mute signal sent to the console’s Solo system (See Master section for details on the Solo system functions).

All Mono and Stereo

®

Inputs, along with the

 

8 groups and L-R, can be

directly assigned to the

 

Mono bus.

 

Use the Matrix Sends

®

to create additional

 

mixes from the 11 main

 

buses (8 Groups, Left,

 

Right and Mono).These

 

additional mixes can be tailored to suit a specific need. Mix-in the signals you need or enhance the main-mix by adding addi- tional instruments where needed.

p. 37

Page 36 Page 38
Image 37
Page 36 Page 38
Contents Hpwtm Mixing Console Page HPW Page Sound Level dBA, Slow Response Important Safety InstructionsBewahren SIE Diese Sicherheitshinweise AUF Gardez CES Instructions Guarde Estas Instrucciones Page Table of contents Mute Block diagramMono Output +48VTALKBACK If the channel peak LED is Mono inputAux send features EQ featuresAux send level Bus assignment featuresBus assign Mono Left- RightChannel monitoring features Channel muting featuresChannel fader HPW Input Mono input optionsHPW Input EQ PCB lower User options HPW Mono InputAux PRE option Direct out D.O. optionRear panel features 4features overviewAutomix Automix optionalStereo input options Both in the OUT position true stereo signal passes throughStereo inputs Affected by the Mute switchBus Assign Signal monitoring featuresHPW Input EQ PCB upper 5stereo input optionsSB7 HPW Stereo InputRear panel connectors 6groups audio subgroups FeaturesGroups Group monitoring features6groups Using the HPW as a monitor consoleFader-reverse function Fader reverse w/LEDCreating additional mixes Group mixing featuresGroup output 1/4TRS jack Group connectors- rear panelInsert jack 1/4TRS jack Auxes auxiliary mixes Auxes50 PK/Sig LED 51 AFL7auxes Aux connectors-rear panelAux output 1/4TRS and male XLR jacks Insert jack 1/4TRS jackLeft right FeaturesLeft and right main audio buses 57 PK/Sig LEDUse the Fader 8left rightMono main audio bus Mono output63 100mm Fader 64 PK/Sig LEDLeft right, mono output Mono connectors- rear panelMain Mono output male XLR jack Matrix mix Matrix mixMatrix output 1/4TRS jack ¡master section Lo cut switchGain Stereo lo-cut filterAux 1/2 or 9/10 selector button Master section ¡Aux sends 1-2 or Stereo fader Master sectionBus Assign Mono Groups78 PK/Sig LED Alternate outputs features Gain reduction metering MasterLimiter CompressorHigh frequency- HF Ambience inputs featuresLow frequency- LF BalanceLevel 99 PREMute Mute levelMaster section monitoring and control ¡ master sectionMonitor metering Source select switchesMonitor output 1/4TRS jack rear panel Selected to avoid errorsSolo operation Solo meteringSingle scene mode Mute scene edit/cancelPresets Headphone sourceLamp connectors Power supply monitorTalkback input On-off switch Power supply internalExt DC Connector Internal supplyExternal power supply front External power supply rear Power supplyPower supply controls rear AC input Power supply controls frontDC status DC outputPower supply dual hookup External Power SupplyPowering the HPW Power supply dual+/- 18 volts @ 3 amps Main analog rails £ specifications
Top Page Image Contents