Crest Audio HPW owner manual 99 PRE, Level, Mute level

Page 47

master section ¡

98aux send level 5-8

These knobs adjust the amount of signal sent to the corresponding AUX buses. Unity gain occurs at the zero setting, with 6dB additional gain available above that. Note:The Aux Sends default to buses 5-8. To send to auxes 1-4 internal solder blob jumbers are avail- able.

NOTE:Whenchang-			+
NOTE:Whenchang-
ing	the aux	sends,
be	certain	to cut

and solder in correct pairs (aux 1/5, 2/6, 3/7, and 4/8.) For example, if changing to Aux 1, be certain to remove the solder on Aux 5.

99PRE

The default signal source for these AUX SENDS is post-fader. These switches are used for selecting the Pre-fader signals for Auxes 5-8 (or 1-4 if solder blobs have been changed). The normal Pre-fader signal is derived Post-EQ.

When button is in the “OUT” position, aux sends are Post-EQ, Post-fader. When button is in the “IN” position, aux sends are Post-insert, Post-EQ, Pre-fader.

100level

This knob adjust the amount of signal sent from the ambience input to the assigned bus and to the ambient level controls on the alternate outputs. Unity gain occurs at the zero setting, with 10dB additional gain available above that.

98

101mute

This button toggles between the ambience output level (100) and the mute level. The LED illuminates when mute is active. The ambi- ence mute functions through the programmable mute scenes.

When button is in the “OUT” position, the level is controled by the ambience level (100).

When button is in the “IN” position, the level is controlled by the mute level (102).

+

Setting the ambience mute level allows the user to preset two ambi-

ence levels. Use the ambi- ence mute button to select the mute level for spoken word and the main ambi- ence level for music.

99

102

100

102mute level

This knob adjusts the amount of signal sent from the ambience input to the assigned bus when the mute button has been engaged. Unity gain occurs at the zero setting, with 10dB additional gain available above that.

101

p. 47

Image 47

Contents Hpwtm Mixing Console Page HPW Page Sound Level dBA, Slow Response Important Safety InstructionsBewahren SIE Diese Sicherheitshinweise AUF Gardez CES Instructions Guarde Estas Instrucciones Page Table of contents Mute Block diagramMono Output +48VTALKBACK If the channel peak LED is Mono inputAux send features EQ featuresLeft- Right Bus assignment featuresAux send level Bus assign MonoChannel fader Channel muting featuresChannel monitoring features HPW Input EQ PCB lower Mono input optionsHPW Input Direct out D.O. option HPW Mono InputUser options Aux PRE optionRear panel features 4features overviewAutomix Automix optionalStereo input options Both in the OUT position true stereo signal passes throughStereo inputs Affected by the Mute switchBus Assign Signal monitoring featuresHPW Input EQ PCB upper 5stereo input optionsSB7 HPW Stereo InputRear panel connectors 6groups audio subgroups FeaturesGroups Group monitoring featuresFader reverse w/LED Using the HPW as a monitor console6groups Fader-reverse functionCreating additional mixes Group mixing featuresInsert jack 1/4TRS jack Group connectors- rear panelGroup output 1/4TRS jack 51 AFL AuxesAuxes auxiliary mixes 50 PK/Sig LEDInsert jack 1/4TRS jack Aux connectors-rear panel7auxes Aux output 1/4TRS and male XLR jacks57 PK/Sig LED FeaturesLeft right Left and right main audio busesUse the Fader 8left right64 PK/Sig LED Mono outputMono main audio bus 63 100mm FaderMain Mono output male XLR jack Mono connectors- rear panelLeft right, mono output Matrix output 1/4TRS jack Matrix mixMatrix mix Stereo lo-cut filter Lo cut switch¡master section GainAux sends 1-2 or Master section ¡Aux 1/2 or 9/10 selector button Groups Master sectionStereo fader Bus Assign Mono78 PK/Sig LED Alternate outputs features Compressor MasterGain reduction metering LimiterBalance Ambience inputs featuresHigh frequency- HF Low frequency- LFMute level 99 PRELevel MuteMaster section monitoring and control ¡ master sectionMonitor metering Source select switchesSolo metering Selected to avoid errorsMonitor output 1/4TRS jack rear panel Solo operationHeadphone source Mute scene edit/cancelSingle scene mode PresetsTalkback input Power supply monitorLamp connectors Internal supply Power supply internalOn-off switch Ext DC ConnectorExternal power supply front External power supply rear Power supplyDC output Power supply controls frontPower supply controls rear AC input DC statusPower supply dual hookup External Power SupplyPowering the HPW Power supply dual+/- 18 volts @ 3 amps Main analog rails £ specifications