Crest Audio HPW owner manual Stereo inputs, Rear panel connectors

Page 27

5stereo inputs

HPWTM owner’s manual

rear panel connectors

The connectors associated with all the Stereo Inputs are located on the rear panel. Line Input 1 has 1/4” TRS jacks, Line Input 2 has unbalanced RCA inputs. The TRS inputs are balanced and can accept either balanced or unbalanced signals.

direct out, 1/4"TRS jack - The input channel's signal is available at this output jack. The default signal routing is derived Pre-fader/Post-EQ. This can be changed by an internal option to Post-insert/Pre-EQ. The output jack is TRS, tip = left, ring = right, sleeve = ground.

line 2, RCA input jack - These RCA input connectors are active when Line 2 is selected

line 1, 1/4"TRS jack - These 1/4” TRS input connectors can be used for balanced or unbalanced sources and are active when the Line 2 switch is in the “UP” position.

p.27

Image 27

Contents Hpwtm Mixing Console Page HPW Page Sound Level dBA, Slow Response Important Safety InstructionsBewahren SIE Diese Sicherheitshinweise AUF Gardez CES Instructions Guarde Estas Instrucciones Page Table of contents Mute Block diagramMono Output +48VTALKBACK If the channel peak LED is Mono inputAux send features EQ featuresLeft- Right Bus assignment featuresAux send level Bus assign MonoChannel muting features Channel monitoring featuresChannel fader Mono input options HPW InputHPW Input EQ PCB lower Direct out D.O. option HPW Mono InputUser options Aux PRE optionRear panel features 4features overviewAutomix Automix optionalStereo input options Both in the OUT position true stereo signal passes throughStereo inputs Affected by the Mute switchBus Assign Signal monitoring featuresHPW Input EQ PCB upper 5stereo input optionsSB7 HPW Stereo InputRear panel connectors 6groups audio subgroups FeaturesGroups Group monitoring featuresFader reverse w/LED Using the HPW as a monitor console6groups Fader-reverse functionCreating additional mixes Group mixing featuresGroup connectors- rear panel Group output 1/4TRS jackInsert jack 1/4TRS jack 51 AFL AuxesAuxes auxiliary mixes 50 PK/Sig LEDInsert jack 1/4TRS jack Aux connectors-rear panel7auxes Aux output 1/4TRS and male XLR jacks57 PK/Sig LED FeaturesLeft right Left and right main audio busesUse the Fader 8left right64 PK/Sig LED Mono outputMono main audio bus 63 100mm FaderMono connectors- rear panel Left right, mono outputMain Mono output male XLR jack Matrix mix Matrix mixMatrix output 1/4TRS jack Stereo lo-cut filter Lo cut switch¡master section GainMaster section ¡ Aux 1/2 or 9/10 selector buttonAux sends 1-2 or Groups Master sectionStereo fader Bus Assign Mono78 PK/Sig LED Alternate outputs features Compressor MasterGain reduction metering LimiterBalance Ambience inputs featuresHigh frequency- HF Low frequency- LFMute level 99 PRELevel MuteMaster section monitoring and control ¡ master sectionMonitor metering Source select switchesSolo metering Selected to avoid errorsMonitor output 1/4TRS jack rear panel Solo operationHeadphone source Mute scene edit/cancelSingle scene mode PresetsPower supply monitor Lamp connectorsTalkback input Internal supply Power supply internalOn-off switch Ext DC ConnectorExternal power supply front External power supply rear Power supplyDC output Power supply controls frontPower supply controls rear AC input DC statusPower supply dual hookup External Power SupplyPowering the HPW Power supply dual+/- 18 volts @ 3 amps Main analog rails £ specifications