Crest Audio owner manual 6groups, Fader-reverse function, Using the HPW as a monitor console

Page 30

6groups

HPWTM owner’s manual

 

 

 

fader-reverse function

using the HPW as a monitor console

Because of its 10 Aux sends, the HPW can be used as a 10-output Monitor mixer. Each input channel can access all of the individual Aux mixes, allowing 10 unique mixes to be generated. Normally, the output level of each of these Aux mixes is controlled by the corresponding Aux Master rotary level pot. In situations where the HPW is to be used as a dedicated Monitor Mixer, the 100mm faders can be switched-over to control the Aux outputs instead of the rotary controls by use of the Fader-Reverse switch. Other controls, associated with monitoring the signals, also change functions when this switch is used.

NOTE: These following controls are ALWAYS fed from the Group audio signal, the Fader-Reverse switch does not affect their function.

Matrix Sends M1 and M2: Always fed from post-level/post-mute Group audio, or in PRE position, from the post-insert/pre-level/pre-mute Group audio.

Group Pan: Always fed from the post-level/post-mute Group audio.

Bus Assignment Mono and L-R: Always fed from the post-level/post-mute Group audio.

45 fader reverse w/LED

When this switch is up (LED Off), the following controls perform these listed functions:

Mute (w/Led): Mutes the Post-fader Group output

100mm Fader: Controls the Group output level

Lower AFL switch (below fader): Monitors the Group level via the Solo system

Upper Rotary pot:: Controls the Aux output level

Upper AFL switch: Monitors the Aux level via the Solo system

When this switch is down (LED On), the following controls perform these listed func- tions:

Mute (w/Led): Mutes the Post-fader Aux output

100mm Fader: Controls the Aux output level

Lower AFL switch (below fader): Monitors the Aux level via the Solo system

Upper Rotary pot:: Controls the Group output level

Upper AFL switch: Monitors the Group level via the Solo system

The overall purpose of this reverse switch is to give the operator easier access to the

45

Aux level and control functions. It shifts the Aux controls to the lower, fader-area of the module when used as a Monitor console.The Group controls are shifted to the upper-

rotary area, since the assignable Groups are not often used in a Monitor console.

Use the Fader-Reverse switches whenever it is beneficial to have an Aux level control on ® a fader.These switches can be used individually (if only 1 Aux needs to be controlled), or all can be switched when a full Monitor Console function is desired.

p.30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Hpwtm Mixing Console Page HPW Page Important Safety Instructions Sound Level dBA, Slow ResponseBewahren SIE Diese Sicherheitshinweise AUF Gardez CES Instructions Guarde Estas Instrucciones Page Table of contents Block diagram MuteMono Output +48VTALKBACK Mono input If the channel peak LED isEQ features Aux send featuresBus assign Mono Bus assignment featuresAux send level Left- RightChannel muting features Channel monitoring featuresChannel fader Mono input options HPW InputHPW Input EQ PCB lower Aux PRE option HPW Mono InputUser options Direct out D.O. option4features overview Rear panel featuresAutomix optional AutomixBoth in the OUT position true stereo signal passes through Stereo input optionsAffected by the Mute switch Stereo inputsSignal monitoring features Bus Assign5stereo input options HPW Input EQ PCB upperHPW Stereo Input SB7Rear panel connectors Features 6groups audio subgroupsGroup monitoring features GroupsFader-reverse function Using the HPW as a monitor console6groups Fader reverse w/LEDGroup mixing features Creating additional mixesGroup connectors- rear panel Group output 1/4TRS jackInsert jack 1/4TRS jack 50 PK/Sig LED AuxesAuxes auxiliary mixes 51 AFLAux output 1/4TRS and male XLR jacks Aux connectors-rear panel7auxes Insert jack 1/4TRS jackLeft and right main audio buses FeaturesLeft right 57 PK/Sig LED8left right Use the Fader63 100mm Fader Mono outputMono main audio bus 64 PK/Sig LEDMono connectors- rear panel Left right, mono outputMain Mono output male XLR jack Matrix mix Matrix mixMatrix output 1/4TRS jack Gain Lo cut switch¡master section Stereo lo-cut filterMaster section ¡ Aux 1/2 or 9/10 selector buttonAux sends 1-2 or Bus Assign Mono Master sectionStereo fader Groups78 PK/Sig LED Alternate outputs features Limiter MasterGain reduction metering CompressorLow frequency- LF Ambience inputs featuresHigh frequency- HF BalanceMute 99 PRELevel Mute level¡ master section Master section monitoring and controlSource select switches Monitor meteringSolo operation Selected to avoid errorsMonitor output 1/4TRS jack rear panel Solo meteringPresets Mute scene edit/cancelSingle scene mode Headphone sourcePower supply monitor Lamp connectorsTalkback input Ext DC Connector Power supply internalOn-off switch Internal supplyPower supply External power supply front External power supply rearDC status Power supply controls frontPower supply controls rear AC input DC outputExternal Power Supply Power supply dual hookupPower supply dual Powering the HPW£ specifications +/- 18 volts @ 3 amps Main analog rails
Top Page Image Contents