Crest Audio HPW owner manual Left right, mono output, Mono connectors- rear panel

Page 38

9left - right, mono output

HPWTM owner’s manual

L/R and mono connectors- rear panel

The HPW Mono output connections are located on the Master rear output panel. The output features a male XLR output connector, along with a 1/4” TRS Insert con- nector. The output is a servo balanced XLR jack.

The TRS Insert jack is wired as Tip=Send, Ring=Return, Sleeve= Audio Ground.This is the “industry-standard” wiring scheme for most single-jack inserts.The Insert send- point is located directly after the main mix amp. The Insert return feeds the top of the 100mm fader.

66main Mono output - male XLR jack

The main output signal is available at this output jack. Pin2 is +Drive, Pin3 is -Drive, Pin1 is Chassis Ground

Drive impedance is (50Ω each leg) Nominal Operating Level= +4dBu

Max Output Level= +26dBu (into 2kΩ or higher)

67insert jack 1/4"TRS jack

This switching 1/4” TRS jack allows an external signal processor to be inserted into the signal path of the main audio bus. The tip carries the SEND signal from the bus, and the ring carries the RETURN signal back to the aux. The Insert-Send point is located directly after the main mix amp. The Return comes back at the top of the main level control.

Tip is Send, Ring is Return, Sleeve is Audio Ground. Send (output) impedance is 50Ω

Return (input) impedance is 5KΩ Nominal Operating Level= -2dBu

NOTE: To avoid any degradation of the HPW’s signal path, any processing gear patched into the insert jack should have a low impedance output (<100Ω) and must be capable of cleanly driving a 2KΩ load to +21dBu.

66 67

p.38

Image 38

Contents Hpwtm Mixing Console Page HPW Page Important Safety Instructions Sound Level dBA, Slow ResponseBewahren SIE Diese Sicherheitshinweise AUF Gardez CES Instructions Guarde Estas Instrucciones Page Table of contents Block diagram MuteMono Output +48VTALKBACK Mono input If the channel peak LED isEQ features Aux send featuresBus assign Mono Bus assignment featuresAux send level Left- RightChannel fader Channel muting featuresChannel monitoring features HPW Input EQ PCB lower Mono input optionsHPW Input Aux PRE option HPW Mono InputUser options Direct out D.O. option4features overview Rear panel featuresAutomix optional AutomixBoth in the OUT position true stereo signal passes through Stereo input optionsAffected by the Mute switch Stereo inputsSignal monitoring features Bus Assign5stereo input options HPW Input EQ PCB upperHPW Stereo Input SB7Rear panel connectors Features 6groups audio subgroupsGroup monitoring features GroupsFader-reverse function Using the HPW as a monitor console6groups Fader reverse w/LEDGroup mixing features Creating additional mixesInsert jack 1/4TRS jack Group connectors- rear panelGroup output 1/4TRS jack 50 PK/Sig LED AuxesAuxes auxiliary mixes 51 AFLAux output 1/4TRS and male XLR jacks Aux connectors-rear panel7auxes Insert jack 1/4TRS jackLeft and right main audio buses FeaturesLeft right 57 PK/Sig LED8left right Use the Fader63 100mm Fader Mono outputMono main audio bus 64 PK/Sig LEDMain Mono output male XLR jack Mono connectors- rear panelLeft right, mono output Matrix output 1/4TRS jack Matrix mixMatrix mix Gain Lo cut switch¡master section Stereo lo-cut filterAux sends 1-2 or Master section ¡Aux 1/2 or 9/10 selector button Bus Assign Mono Master sectionStereo fader Groups78 PK/Sig LED Alternate outputs features Limiter MasterGain reduction metering CompressorLow frequency- LF Ambience inputs featuresHigh frequency- HF BalanceMute 99 PRELevel Mute level¡ master section Master section monitoring and controlSource select switches Monitor meteringSolo operation Selected to avoid errorsMonitor output 1/4TRS jack rear panel Solo meteringPresets Mute scene edit/cancelSingle scene mode Headphone sourceTalkback input Power supply monitorLamp connectors Ext DC Connector Power supply internalOn-off switch Internal supplyPower supply External power supply front External power supply rearDC status Power supply controls frontPower supply controls rear AC input DC outputExternal Power Supply Power supply dual hookupPower supply dual Powering the HPW£ specifications +/- 18 volts @ 3 amps Main analog rails