Multiquip WM63H8, WM63H5 manual Basic engine, Initial Servicing

Page 18

basic engine

10

9

1

2

2.

Throttle Lever — Used to adjust engine RPM speed

 

(lever advanced forward SLOW, lever back toward

 

operator FAST).

3.

Engine ON/OFF Switch — ON position permits engine

 

starting, OFF position stops engine operations.

4.

Recoil Starter (pull rope) Manual-starting method.

 

Pull the starter grip until resistance is felt, then pull

8

3

7

6

5

4

Figure 11. Engine Components

Initial Servicing

The engine (Figure 11) must be checked for proper lubrication and filled with fuel prior to operation. Refer to the engine manufacturer’s manual for instructions and details of operation and servicing.

1.Fuel Filler Cap — Remove this cap to add unleaded gasoline to the fuel tank. Make sure cap is tightened securely. DO NOT over fill.

DANGER

Adding fuel to the tank should be done only when the engine is stopped and has had an opportunity to cool down. In the event of a fuel spill, DO NOT attempt to start the engine until the fuel residue has

been completely wiped up, and the area surrounding the engine is dry.

 

briskly and smoothly.

5.

Fuel Valve Lever — OPEN to let fuel flow, CLOSE to

 

stop the flow of fuel.

6.

Choke Lever — Used in the starting of a cold engine,

 

or in cold weather conditions. The choke enriches the

 

fuel mixture.

7.

Air Cleaner — Prevents dirt and other debris from

 

entering the fuel system. Remove wing-nut on top of

 

air filter cannister to gain access to filter element.

NOTICE

Operating the engine without an air filter, with a damaged air filter, or a filter in need of replacement will allow dirt to enter the engine, causing rapid engine wear.

WARNING

Engine components can generate extreme heat. To prevent burns, DO NOT touch these areas while the engine is running or immediately after operating.NEVER operate the engine with the muffler removed.

8.Spark Plug — Provides spark to the ignition system. Set spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean spark plug once a week.

9.Muffler — Used to reduce noise and emissions.

10.Fuel Tank — Holds unleaded gasoline. For additional information refer to engine owner's manual.

page 18 — wm63-series Mixer • operation and parts manual — rev. #0 (09/27/12)

Image 18
Contents MODELs WM63H5, wm63h8 Wm63e Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningTable of Contents WM63H5/WM63H8/WM63E Plaster And Mortar MixersChoose from three easy options Explosive fuel hazards Safety informationSaFeTY messages Burn hazardsGeneral saFeTY Mixer saFeTY Engine saFeTY gasoline models onlYBefore servicing equipment EleCTriC moTor saFeTY eleCTriC models onlY Fuel saFeTY gasoline models onlYGeneraTor saFeTY Power Cord/Cable safetyTowing saFeTY EnvironmenTal saFeTY„ alwaYs shutdown engine before transporting Safety chain connection Tow Bar to Mixer ConnectionSpecifications Mixer SpecificationsDimensions DimensionsGeneral information Components Mixer ComponentsEngine Oil Check InspectionBefore Starting Fuel CheckStart/Stop Switch Belt CheckGrease Fittings Dumping Mechanism Basic engine Initial ServicingElectric motor Electric MotorElectric Motor Connection Electric Motor Voltage Switch Recommended Extension Cord SizesPaddle blade adjustment Adjust paddles as shown in FigureTurn the engine switch to the on position Start-upBelt Slip Lever Start/Stop Position Stopping the Mixer Gasoline OperationMixing/Dumping Stopping the Mixer electric motorPage Maintenance engine First EveryEngine air cleaner Install drain bolt with sealing washer and tighten securelyEngine oil Drum Head Seals Maintenance MixerBall Socket and Clamp Face Maintenance Drum Bearing Bracket LubricationWheel Bearings Main Gear and Drive Pinion AlignmentInspectTooth Contact between Main Gear and Drive Pinion Tires/Wheels/Lug Nuts Grease Fittings Zerk Maintenance Electric MotorGear Lubrication Tires Wear/InflationLug Nut Torque Requirements Start all wheel lug nuts by handNever use an pneumatic air gun to tighten wheel lug nuts Mixer Cleaning SuspensionMixer Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Replace seals Adjust if necessaryDrum difficult to discharge tilt Blades adjusted too tight Defective or worn drum supportWiring diagram Explanation of Code in Remarks Column Suggested Spare Parts Qty DescriptionSafety Instructions Nameplate and decalsPart Name QTY Remarks 521232 Decal, inspect before towingFrame assy 530023 514842491692 507444Paddle shaft assy 3215 SCREW, HHC 1/2-13 X 3-1/2 EM200292 514752492584 NUT, Lock 1/2 530140C 530141Steel tub assy Part Front Frame Rear Frame20561-001 5300283249 491008Drum and paddle shaft complete assy 07594-012 Roll PIN 3/16 X 3/4 20654-001 516069EM969013 NUT, Lock 3/8 3019092 EM961019Axle assy 516476 346929194 8164Engine assy 513868 EM905016492378 Bolt 3/8 NC X 1-3/4 G5 JISB2804C25 500214 KEY, Square 1/4 X 1/4 X 1-1/2 502226Electric motor assy 492582 NUT, Nylon 5/16-18 35L229S302 492378 Bolt 3/8 X 1-3/4 G5 20216-00120061-001 502213Cabinet assy 11213287 515014490202 2203Terms and conditions of sale parts FreigHT poliCYPage HERE’S HOW to GET Help