Multiquip WM63H8 manual Safety information, SaFeTY messages, Explosive fuel hazards, Burn hazards

Page 6

safety information

Do not operate or service the equipment before reading the entire manual. Safety precautions should be followed at all times when operating this equipment.

Failure to read and understand the safety messages and operating instructions could result in injury to yourself and others.

saFeTY messages

The four safety messages shown below will inform you about potential hazards that could injure you or others.The safety messages specifi cally address the level of exposure to the operator and are preceded by one of four words: danger, warning, CauTion or noTiCe.

saFeTY sYmBols

danger

Indicates a hazardous situation which, if not avoided, will result in deaTH or serious inJurY.

warning

Indicates a hazardous situation which, if not avoided, Could result in deaTH or serious inJurY.

CauTion

Indicates a hazardous situation which, if not avoided, Could result in minor or moderaTe inJurY.

NOTICE

Addresses practices not related to personal injury.

Potential hazards associated with the operation of this equipment will be referenced with hazard symbols which may appear throughout this manual in conjunction with safety messages.

Symbol	Safety Hazard
	Lethal exhaust gas hazards
	Explosive fuel hazards
	Burn hazards
	Rotating parts hazards

page 6 — wm63-series Mixer • operation and parts manual — rev. #0 (09/27/12)

Image 6

Contents MODELs WM63H5, wm63h8 Wm63e Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningTable of Contents WM63H5/WM63H8/WM63E Plaster And Mortar MixersChoose from three easy options Explosive fuel hazards Safety informationSaFeTY messages Burn hazardsGeneral saFeTY Mixer saFeTY Engine saFeTY gasoline models onlYBefore servicing equipment EleCTriC moTor saFeTY eleCTriC models onlY Fuel saFeTY gasoline models onlYGeneraTor saFeTY Power Cord/Cable safetyTowing saFeTY EnvironmenTal saFeTY„ alwaYs shutdown engine before transporting Safety chain connection Tow Bar to Mixer ConnectionSpecifications Mixer SpecificationsDimensions DimensionsGeneral information Components Mixer ComponentsEngine Oil Check InspectionBefore Starting Fuel CheckStart/Stop Switch Belt CheckGrease Fittings Dumping Mechanism Basic engine Initial ServicingElectric motor Electric MotorElectric Motor Connection Electric Motor Voltage Switch Recommended Extension Cord SizesPaddle blade adjustment Adjust paddles as shown in FigureTurn the engine switch to the on position Start-upBelt Slip Lever Start/Stop Position Stopping the Mixer Gasoline OperationMixing/Dumping Stopping the Mixer electric motorPage Maintenance engine First EveryEngine air cleaner Install drain bolt with sealing washer and tighten securelyEngine oil Drum Head Seals Maintenance MixerBall Socket and Clamp Face Maintenance Drum Bearing Bracket LubricationWheel Bearings Main Gear and Drive Pinion AlignmentInspectTooth Contact between Main Gear and Drive Pinion Tires/Wheels/Lug Nuts Grease Fittings Zerk Maintenance Electric MotorGear Lubrication Tires Wear/InflationLug Nut Torque Requirements Start all wheel lug nuts by handNever use an pneumatic air gun to tighten wheel lug nuts Mixer Cleaning SuspensionMixer Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Replace seals Adjust if necessaryDrum difficult to discharge tilt Blades adjusted too tight Defective or worn drum supportWiring diagram Explanation of Code in Remarks Column Suggested Spare Parts Qty DescriptionSafety Instructions Nameplate and decalsPart Name QTY Remarks 521232 Decal, inspect before towingFrame assy 530023 514842491692 507444Paddle shaft assy 3215 SCREW, HHC 1/2-13 X 3-1/2 EM200292 514752492584 NUT, Lock 1/2 530140C 530141Steel tub assy Part Front Frame Rear Frame20561-001 5300283249 491008Drum and paddle shaft complete assy 07594-012 Roll PIN 3/16 X 3/4 20654-001 516069EM969013 NUT, Lock 3/8 3019092 EM961019Axle assy 516476 346929194 8164Engine assy 513868 EM905016492378 Bolt 3/8 NC X 1-3/4 G5 JISB2804C25 500214 KEY, Square 1/4 X 1/4 X 1-1/2 502226Electric motor assy 492582 NUT, Nylon 5/16-18 35L229S302 492378 Bolt 3/8 X 1-3/4 G5 20216-00120061-001 502213Cabinet assy 11213287 515014490202 2203Terms and conditions of sale parts FreigHT poliCYPage HERE’S HOW to GET Help