Multiquip WM63H5, WM63H8 manual Mixer Storage

Page 33

maintenance (Mixer)

Mixer Storage

For storage of the mixer for over 30 days, the following is recommended:

Drain the fuel tank completely, or add STA-BIL to the fuel. Run the engine until the fuel is completely consumed.

Completely drain used oil from the engine crankcase and fill with fresh clean oil, then follow the procedures described in the engine manual for engine storage.

Clean the entire mixer and engine compartment.

Place the mixing drum in the down position (mouth facing downward).

Cover the mixer and place it a clean dry area, that is protected from harsh elements.

WM63-series Mixer • operation and parts manual — rev. #0 (069/27/12) — page 33

Image 33

Contents MODELs WM63H5, wm63h8 Wm63e Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsWM63H5/WM63H8/WM63E Plaster And Mortar Mixers Table of ContentsChoose from three easy options SaFeTY messages Safety informationExplosive fuel hazards Burn hazardsGeneral saFeTY Mixer saFeTY Engine saFeTY gasoline models onlYBefore servicing equipment GeneraTor saFeTY Fuel saFeTY gasoline models onlYEleCTriC moTor saFeTY eleCTriC models onlY Power Cord/Cable safetyTowing saFeTY EnvironmenTal saFeTY„ alwaYs shutdown engine before transporting Tow Bar to Mixer Connection Safety chain connectionMixer Specifications SpecificationsDimensions DimensionsGeneral information Mixer Components ComponentsBefore Starting InspectionEngine Oil Check Fuel CheckStart/Stop Switch Belt CheckGrease Fittings Dumping Mechanism Initial Servicing Basic engineElectric motor Electric MotorElectric Motor Connection Recommended Extension Cord Sizes Electric Motor Voltage SwitchAdjust paddles as shown in Figure Paddle blade adjustmentStart-up Turn the engine switch to the on positionBelt Slip Lever Start/Stop Position Mixing/Dumping OperationStopping the Mixer Gasoline Stopping the Mixer electric motorPage First Every Maintenance engineEngine air cleaner Install drain bolt with sealing washer and tighten securelyEngine oil Ball Socket and Clamp Face Maintenance Maintenance MixerDrum Head Seals Drum Bearing Bracket LubricationWheel Bearings Main Gear and Drive Pinion AlignmentInspectTooth Contact between Main Gear and Drive Pinion Gear Lubrication Grease Fittings Zerk Maintenance Electric MotorTires/Wheels/Lug Nuts Tires Wear/InflationLug Nut Torque Requirements Start all wheel lug nuts by handNever use an pneumatic air gun to tighten wheel lug nuts Suspension Mixer CleaningMixer Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Drum difficult to discharge tilt Blades adjusted too tight Adjust if necessaryReplace seals Defective or worn drum supportWiring diagram Explanation of Code in Remarks Column Qty Description Suggested Spare PartsNameplate and decals Safety Instructions521232 Decal, inspect before towing Part Name QTY RemarksFrame assy 491692 514842530023 507444Paddle shaft assy 492584 NUT, Lock 1/2 530140C 5147523215 SCREW, HHC 1/2-13 X 3-1/2 EM200292 530141Part Front Frame Rear Frame Steel tub assy3249 53002820561-001 491008Drum and paddle shaft complete assy EM969013 NUT, Lock 3/8 3019092 51606907594-012 Roll PIN 3/16 X 3/4 20654-001 EM961019Axle assy 29194 3469516476 8164Engine assy 492378 Bolt 3/8 NC X 1-3/4 G5 JISB2804C25 EM905016513868 500214 KEY, Square 1/4 X 1/4 X 1-1/2 502226Electric motor assy 20061-001 492378 Bolt 3/8 X 1-3/4 G5 20216-001492582 NUT, Nylon 5/16-18 35L229S302 502213112 Cabinet assy490202 51501413287 2203FreigHT poliCY Terms and conditions of sale partsPage HERE’S HOW to GET Help