Multiquip WM63H5, WM63H8 manual Suggested Spare Parts, Qty Description

Page 39

Suggested Spare Parts

Wm63-series plaster and mortar mixer with

honda GX160UT1HX2/gx240UT1HA2 engines and 1.5 HP electric motor. 1 to 3 units

Qty.

P/N

description

6

491107

V-BELT A32, HONDA ENGINE (GX160, 5.5 HP)

6

07055-034

V-BELT 4l340, HONDA ENGINE (GX240, 8.0 HP)

6

491112

V-BELT A40, ELECTRIC MOTOR

2

EM914288

OIL SEAL, AXLE

4

EM903113

BEARING, CONE, AXLE

4

EM903012

BEARING, CUP, AXLE

2

20654-001

SEAL, PADDLE SHAFT (BLACK)

2

530029

RING, RETENTION

2

20104-002

SEAL, SHAFT URETHANE (YELLOW)

3

17210ZE1822

ELEMENT, AIR CLEANER (GX160, 5.5 HP)

3

17210ZE2822

ELEMENT, AIR CLEANER (GX240, 8.0 HP)

3

9807956846

SPARK PLUG, BPR6ES, NGK

3

9807956855

SPARK PLUG, W20EPR-U, DENSO

1

28462ZH8003

ROPE, RECOIL STARTER (GX160, 5.5 HP)

1

28462ZE2W11

ROPE, RECOIL STARTER (GX240, 8.0 HP)

1

17620Z4H020

CAP, FUEL TANK

2

25647-502

KIT, WIPER BLADES (STEEL DRUM)

NOTICE

Part numbers on this Suggested Spare Parts list may supersede/replace the part numbers shown in the following parts lists.

WM63-series Mixer • operation and parts manual — rev. #0 (069/27/12) — page 39

Image 39
Contents MODELs WM63H5, wm63h8 Wm63e Proposition 65 Warning Silicosis Warning Silicosis/Respiratory WarningsWM63H5/WM63H8/WM63E Plaster And Mortar Mixers Table of ContentsChoose from three easy options Burn hazards Safety informationSaFeTY messages Explosive fuel hazardsGeneral saFeTY Mixer saFeTY Engine saFeTY gasoline models onlYBefore servicing equipment Power Cord/Cable safety Fuel saFeTY gasoline models onlYGeneraTor saFeTY EleCTriC moTor saFeTY eleCTriC models onlYTowing saFeTY EnvironmenTal saFeTY„ alwaYs shutdown engine before transporting Tow Bar to Mixer Connection Safety chain connectionMixer Specifications SpecificationsDimensions DimensionsGeneral information Mixer Components ComponentsFuel Check InspectionBefore Starting Engine Oil CheckStart/Stop Switch Belt CheckGrease Fittings Dumping Mechanism Initial Servicing Basic engineElectric motor Electric MotorElectric Motor Connection Recommended Extension Cord Sizes Electric Motor Voltage SwitchAdjust paddles as shown in Figure Paddle blade adjustmentStart-up Turn the engine switch to the on positionBelt Slip Lever Start/Stop Position Stopping the Mixer electric motor OperationMixing/Dumping Stopping the Mixer GasolinePage First Every Maintenance engineEngine air cleaner Install drain bolt with sealing washer and tighten securelyEngine oil Drum Bearing Bracket Lubrication Maintenance MixerBall Socket and Clamp Face Maintenance Drum Head SealsWheel Bearings Main Gear and Drive Pinion AlignmentInspectTooth Contact between Main Gear and Drive Pinion Tires Wear/Inflation Grease Fittings Zerk Maintenance Electric MotorGear Lubrication Tires/Wheels/Lug NutsLug Nut Torque Requirements Start all wheel lug nuts by handNever use an pneumatic air gun to tighten wheel lug nuts Suspension Mixer CleaningMixer Storage Troubleshooting engine TroubleshootingAir cleaner dirty? Clean or replace air cleaner Defective or worn drum support Adjust if necessary Drum difficult to discharge tilt Blades adjusted too tight Replace sealsWiring diagram Explanation of Code in Remarks Column Qty Description Suggested Spare PartsNameplate and decals Safety Instructions521232 Decal, inspect before towing Part Name QTY RemarksFrame assy 507444 514842491692 530023Paddle shaft assy 530141 514752492584 NUT, Lock 1/2 530140C 3215 SCREW, HHC 1/2-13 X 3-1/2 EM200292Part Front Frame Rear Frame Steel tub assy491008 5300283249 20561-001Drum and paddle shaft complete assy EM961019 516069EM969013 NUT, Lock 3/8 3019092 07594-012 Roll PIN 3/16 X 3/4 20654-001Axle assy 8164 346929194 516476Engine assy 500214 KEY, Square 1/4 X 1/4 X 1-1/2 502226 EM905016492378 Bolt 3/8 NC X 1-3/4 G5 JISB2804C25 513868Electric motor assy 502213 492378 Bolt 3/8 X 1-3/4 G5 20216-00120061-001 492582 NUT, Nylon 5/16-18 35L229S302112 Cabinet assy2203 515014490202 13287FreigHT poliCY Terms and conditions of sale partsPage HERE’S HOW to GET Help