Multiquip WM63H8 Mixer saFeTY, Engine saFeTY gasoline models onlY, Before servicing equipment

Page 8
DANGEROUS
GAS FUMES

safety information

mixer saFeTY

danger

„never operate the equipment in an explosive atmosphere or near combustible materials.An explosion or fi re could result causing severe bodily harm or even death.

„do noT mix flammable or explosive substances.

warning

„ never place your hands inside the drum while starting or operating this equipment.

„ never disconnect any emergency or safety devices. These devices are

intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.

„Before operating mixer, ensure that safety grate is in position and correctly fi tted.

CauTion

„never lubricate components or attempt service on a running machine.

NOTICE

„alwaYs keep the machine in proper running condition.

„alwaYs ensure mixer is on level ground before mixing.

„Fix damage to machine and replace any broken parts immediately.

„do noT tip mixer onto drum mouth when the drum is rotating.

„Ensure the drum is rotating while fi lling and emptying the drum.

„alwaYs store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

engine saFeTY (gasoline models onlY)

danger

„Engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled.

„The engine of this equipment requires an adequate

free fl ow of cooling air. never operate this equipment in any enclosed or narrow

area where free fl ow of the air is restricted. If the air

fl ow is restricted it will cause injury to people and property

and serious damage to the equipment or engine.

warning

„do noT place hands or fingers inside engine compartment when engine is running.

„never operate the engine with heat shields or guards removed.

„Keep fi ngers, hands hair and clothing away

from all moving parts to prevent injury.

„do noT remove the engine oil drain plug

while the engine is hot. Hot oil will gush out of the oil tank and severely scald any persons in the general area of the mixer.

CauTion

„never touch the hot exhaust manifold, muffl er or cylinder. Allow these parts to cool

before servicing equipment.

„Make certain the operator knows how to and is capable of turning the engine OFF in case of an emergency.

NOTICE

„never run engine without an air fi lter or with a dirty air fi lter. Severe engine damage may occur. Service air fi lter frequently to prevent engine malfunction.

„never tamper with the factory settings of the engine or engine governor. Damage to the engine or equipment can result if operating in speed ranges above the maximum allowable.

page 8 — wm63-series Mixer • operation and parts manual — rev. #0 (09/27/12)

Image 8
Contents MODELs WM63H5, wm63h8 Wm63e Proposition 65 Warning Silicosis/Respiratory Warnings Silicosis WarningTable of Contents WM63H5/WM63H8/WM63E Plaster And Mortar MixersChoose from three easy options Safety information SaFeTY messagesExplosive fuel hazards Burn hazardsGeneral saFeTY Before servicing equipment Mixer saFeTYEngine saFeTY gasoline models onlY Fuel saFeTY gasoline models onlY GeneraTor saFeTYEleCTriC moTor saFeTY eleCTriC models onlY Power Cord/Cable safety„ alwaYs shutdown engine before transporting Towing saFeTYEnvironmenTal saFeTY Safety chain connection Tow Bar to Mixer ConnectionSpecifications Mixer SpecificationsDimensions DimensionsGeneral information Components Mixer ComponentsInspection Before StartingEngine Oil Check Fuel CheckGrease Fittings Dumping Mechanism Start/Stop SwitchBelt Check Basic engine Initial ServicingElectric Motor Connection Electric motorElectric Motor Electric Motor Voltage Switch Recommended Extension Cord SizesPaddle blade adjustment Adjust paddles as shown in FigureTurn the engine switch to the on position Start-upBelt Slip Lever Start/Stop Position Operation Mixing/DumpingStopping the Mixer Gasoline Stopping the Mixer electric motorPage Maintenance engine First EveryEngine oil Engine air cleanerInstall drain bolt with sealing washer and tighten securely Maintenance Mixer Ball Socket and Clamp Face MaintenanceDrum Head Seals Drum Bearing Bracket LubricationInspectTooth Contact between Main Gear and Drive Pinion Wheel BearingsMain Gear and Drive Pinion Alignment Grease Fittings Zerk Maintenance Electric Motor Gear LubricationTires/Wheels/Lug Nuts Tires Wear/InflationNever use an pneumatic air gun to tighten wheel lug nuts Lug Nut Torque RequirementsStart all wheel lug nuts by hand Mixer Cleaning SuspensionMixer Storage Troubleshooting Troubleshooting engineAir cleaner dirty? Clean or replace air cleaner Adjust if necessary Drum difficult to discharge tilt Blades adjusted too tightReplace seals Defective or worn drum supportWiring diagram Explanation of Code in Remarks Column Suggested Spare Parts Qty DescriptionSafety Instructions Nameplate and decalsPart Name QTY Remarks 521232 Decal, inspect before towingFrame assy 514842 491692530023 507444Paddle shaft assy 514752 492584 NUT, Lock 1/2 530140C3215 SCREW, HHC 1/2-13 X 3-1/2 EM200292 530141Steel tub assy Part Front Frame Rear Frame530028 324920561-001 491008Drum and paddle shaft complete assy 516069 EM969013 NUT, Lock 3/8 301909207594-012 Roll PIN 3/16 X 3/4 20654-001 EM961019Axle assy 3469 29194516476 8164Engine assy EM905016 492378 Bolt 3/8 NC X 1-3/4 G5 JISB2804C25513868 500214 KEY, Square 1/4 X 1/4 X 1-1/2 502226Electric motor assy 492378 Bolt 3/8 X 1-3/4 G5 20216-001 20061-001492582 NUT, Nylon 5/16-18 35L229S302 502213Cabinet assy 112515014 49020213287 2203Terms and conditions of sale parts FreigHT poliCYPage HERE’S HOW to GET Help